Victory BX510H Скачать руководство пользователя страница 11

Страница: 11 / 74

Operator’s Manual Victory BX510H

- Page 11 of 74 -

Version 2.0

SAFETY INFORMATION

WARNING!

•

Read and understand all Safety measures and Warnings before carrying
out any operation or adjustments.

•

Untrained persons who have not thoroughly read and understood this
manual might never approach the machine.

•

Refer to all safety decals in this manual. Read all instructions noted on
them.

3.1

Introduction

The machine design is such that safe use and maintenance are possible. Anyone who works with it

must know the instructions and regulations stated in this manual.
The owner is responsible for ensuring that users are familiar with the instructions, operating

regulations, and observations.

In this Operator's Manual, there is a distinction between:

Normal / Intended use (see operating instructions).

Other activities such as service and maintenance.

This distinction is because operators must meet other (safety) requirements than the technical

service staff.

The operator performs the daily cleaning and maintenance work described in the operating
instructions.

3.2

Generally Applicable Safety Rules

This list contains general safety measures which must be complied with for personal safety

reasons.

Make sure children and animals cannot come into the machine's vicinity.

Only persons who have read and understood the operating instructions might be in the
machine's vicinity.

Unauthorized persons may not perform acts if the machine is in use.

Never work alone; always make sure that at least one person is nearby.

Do not remove the brought warning stickers or markings.

Always clean the machine properly and keep the workplace free of dirt and obstacles.

Always ensure sufficient ambient lighting.

Содержание BX510H











































































Результаты поиска

Содержание BX510H

Отзывы:

Похожие инструкции для BX510H

Бренды по названию

Популярные бренды

Victory BX510H, Руководство оператора

Результаты поиска

Содержание BX510H

Отзывы:

Похожие инструкции для BX510H

Бренды по названию

Популярные бренды