Victory BX510H Скачать руководство пользователя страница 36

Страница: 36 / 74

Operator’s Manual Victory BX510H

- Page 36 of 74 -

Version 2.0

5.7

Shortening the PTO Shaft Length

Unhook the PTO shaft from the tractor’s output shaft and pull the outer and inner drivelines

apart.

Re-attach the outer driveline to the tractor’s output shaft. Pull on the inner and outer

drivelines to ensure they are adequately secured.

Hold the inner and outer drivelines parallel to each other:

(

) Measure 1” (‘B’ dimension) back from the outer driveline universal joint shield and make

a mark at this location on the inner driveline shield.

(

) Measure 1” (‘B’ dimension) back from the inner driveline universal joint shield and make

a mark at this location on the outer driveline shield.

Remove the drivelines from both the tractor and implement.

Measure from the end of the inner shield to the scribed mark (‘X’ dimension).

Cut off the inner shield at the mark. Cut the same amount off the inner shaft

(‘X1’ dimension).

Measure from the end of the outer shield to the scribed mark (‘Y’ dimension).

Cut off the outer shield at the mark. Cut the same amount off the outer shaft (‘Y1’
dimension).

Remove all burrs.

Check the PTO shaft’s EXTENDED LENGTH as described in the next step.

5.7.1

Checking the PTO Shaft’s Extended Length

Содержание BX510H











































































Результаты поиска

Содержание BX510H

Отзывы:

Бренды по названию

Популярные бренды

Victory BX510H, Руководство оператора

Результаты поиска

Содержание BX510H

Отзывы:

Бренды по названию

Популярные бренды