Victory BX510H Скачать руководство пользователя страница 31

Страница: 31 / 74

Operator’s Manual Victory BX510H

- Page 31 of 74 -

Version 2.0

OPERATION

The features of the BX510H are described in this Chapter to ensure that you can use it to its full

potential.
The operation procedures ensure that every operator uses the BX510H correctly.
Following these procedures will extend the life of the BX510H, creating a safe operating

environment.

WARNINGS and DANGER!

•

Children under the age of 16 should not operate the BX510H.

•

DO NOT operate The BX510H while under the influence of drugs or
alcohol, as severe injury or death could result.

•

Read the Operators manual for the tractor. Follow all safety and
maintenance guidelines in this manual when dealing with the PTO.

•

DO NOT operate the woodchipper for any purpose other than what it is
meant for.

•

DO NOT operate the woodchipper unless all safety guards and
protection plates are in place.

•

DO NOT leave the machine unattended while it is running.

CAUTION:

•

Keep your hands away from all moving components. Rotating parts can
cause severe injury.

•

Don't stand too close to the BX510H. A safe distance is approx.
1 m.

•

No other persons are allowed around the equipment during the
operation.

•

Follow ALL safety guidelines and procedures to ensure safe use of the
BX510H.

5.1

Human

An operator makes the equipment ready for use and starts it as described further in this chapter.

Содержание BX510H











































































Результаты поиска

Содержание BX510H

Отзывы:

Похожие инструкции для BX510H

Бренды по названию

Популярные бренды

Victory BX510H, Руководство оператора

Результаты поиска

Содержание BX510H

Отзывы:

Похожие инструкции для BX510H

Бренды по названию

Популярные бренды