Victory BX510H Скачать руководство пользователя страница 48

Страница: 48 / 74

Operator’s Manual Victory BX510H

- Page 48 of 74 -

Version 2.0

STEP 6:

NOTE:

The pin should be fully inserted in the
three holes as shown.

Use an awl to remove any debris
impacted in the hex recess of the flat
socket cap screws, securing the knife.

Take care to clean the bolt heads
thoroughly to ensure the Allen key bit
socket fits appropriately. If not, you
may strip the heads out. Air blow
guns are also helpful.

STEP 7 Remove and install flywheel knives:

Insert a 6 mm Allen socket wrench
and a 17 mm socket wrench at the
backside to remove the four knife
bolts.

Remove the knife. Be careful not to
drop the fasteners into the flywheel
chamber.

Clean the knife blade recess surface
properly.

Place a new or sharpened knife.

Mount and hand-tighten the
fasteners, including washers.

STEP 8:

Use a torque wrench attached to the
17 mm socket and apply a 40 lbs/ft
torque.

DO NOT over-torque the bolts; knife
breakage can occur.

Remove the lock pin, rotate the
flywheel 90 degrees, and reinstall the
lock pin for the next knife.

Repeat this until all knives are
replaced.

NOTE:

Always use new M10 nuts with

a Nylon lock for the knives.

Содержание BX510H











































































Результаты поиска

Содержание BX510H

Отзывы:

Похожие инструкции для BX510H

Бренды по названию

Популярные бренды

Victory BX510H, Руководство оператора

Результаты поиска

Содержание BX510H

Отзывы:

Похожие инструкции для BX510H

Бренды по названию

Популярные бренды