manualshive.com logo in svg

VIASYS Vmax Encore, Техническое справочное руководство

Поделиться
Скачать
VIASYS Vmax Encore Скачать руководство пользователя страница 7

Technical Reference Manual

Vmax Encore

L2707

1–1

CHAPTER 1

INTRODUCTION

VMAX ENCORE SERIES OVERVIEW

This manual provides procedures relevant to servicing, troubleshooting, and repairing the Vmax 
systems described in the following section. These procedures are intended for service and support 
personnel who have been trained and are authorized to service the Vmax systems.

VMAX INSTRUMENT CONFIGURATIONS

The Vmax Encore Series consists of four basic instrument configurations. All instruments can be 
ordered alone or with a selection of optional housings: a highly mobile cart, a mobile console, or a 
stationary table. These configurations can be utilized separately or hardware/software components 
can be combined in a number of ways to meet the needs of any specific cardiopulmonary 
laboratory. The four available instrument configurations are as follows:

•

Vmax Encore 20 Pulmonary Spirometry Instrument

•

Vmax Encore 22 Pulmonary Function Analysis Instrument

•

Vmax Encore 29 Cardiopulmonary Exercise Testing Instrument

•

Vmax Encore 229 Pulmonary Function/Cardiopulmonary Exercise Testing Instrument

The Vmax Encore module can be positioned horizontally or vertically. The module can have a high 
profile in the horizontal position (a wide profile in the vertical position); or the module can have a 
low profile in the horizontal position (a narrow profile in the vertical position), depending on the 
model. The maximum height in the horizontal position (width in the vertical position) is 15.24 cm. 
Vmax Encore 20, 20c, 29c, and 29s have the low (narrow) profile.
By including or excluding hardware or software features, ten other configurations are available, 
making a total of 14 different instruments. These ten other configurations are as follows:

•

Vmax Encore 20c Pulmonary Spirometry Instrument

•

Vmax Encore 22d Pulmonary Function Analysis Instrument

•

Vmax Encore 22lv Pulmonary Function Analysis Instrument

•

Vmax Encore 29c Cardiopulmonary Exercise Testing Instrument

•

Vmax Encore 29n Cardiopulmonary Exercise Testing Instrument

•

Vmax Encore 29s Cardiopulmonary Exercise Testing Instrument

•

Vmax Encore 229c Pulmonary Function/Cardiopulmonary Exercise Testing Instrument

•

Vmax Encore 229d Pulmonary Function/Cardiopulmonary Exercise Testing Instrument

•

Vmax Encore 229lv Pulmonary Function/Cardiopulmonary Exercise Testing Instrument

•

Vmax Encore 229n Pulmonary Function/Cardiopulmonary Exercise Testing Instrument

Содержание Vmax Encore























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды