manualshive.com logo in svg

VIASYS Vmax Encore, Техническое справочное руководство

Поделиться
Скачать
VIASYS Vmax Encore Скачать руководство пользователя страница 62

Chapter 3 Maintenance and Troubleshooting 

3–8

L2707

Technical Reference Manual

Vmax Encore

b. Select valve

 L 

(DLCO). Turn DLCO Supply OFF. Pressure should not drop by more than 

100 PSI, within 2 minutes. If so, locate source of leak and correct.

c. Turn DLCO supply ON when Leak Test is verified to be OK.

3.

Calibration Gas 1 & 2 Leak Test:
a. Turn Cal Gas 1 supply ON and adjust regulator to 50 PSI.
b. Turn Cal Gas 1 Supply OFF. Pressure should not drop by more than 100 PSI, within 2 

minutes. If so, locate source of leak and correct.

c. Turn Cal Gas supply ON when Leak Test is verified to be OK.
d. Perform same operation for Cal Gas 2 supply.

MASS FLOW SENSOR BOARD ADJUSTMENT PROCEDURES

The test points and adjustment potentiometers for the procedures listed below are located on the 
Mass Flow Sensor Board. The voltages can be monitored with a voltmeter at the designated test 
points or by viewing the voltages on the Diagnostics Test screen.

Figure 3-4  Vmax Program Manager Screen with Diagnostics selected

Содержание Vmax Encore























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды