manualshive.com logo in svg

VIASYS Vmax Encore, Техническое справочное руководство

Поделиться
Скачать
VIASYS Vmax Encore Скачать руководство пользователя страница 38

Chapter 2 System Description 

2–12

L2707

Technical Reference Manual

Vmax Encore

Note:

The blower/fan assembly is only used during metabolic measurement tests. This 
device is not standard in the Vmax Encore 22.

VMAX ENCORE 20 BLOCK DIAGRAM

The Vmax Encore 20 is a Pulmonary Spirometry Instrument. This system does not have a lower 
module. The upper module contains only those hardware devices necessary to perform Pulmonary 
Function spirometry tests and calibrations.

Figure 2-7  

Vmax Encore 20 Block Diagram

Hardware Devices Not Installed:
Being a spirometry only system, the Vmax Encore 20 has no need for sample pumps or gas 
analyzers or the circuit board that controls any of those devices. Therefore, none of these devices 
are installed.

•

Analyzer Control Board

•

Pump and Analyzers Assembly

The following devices are all located in the pneumatics assembly, which is not part of the Vmax 
Encore 20 Instrument.

•

Demand Valve

•

3-Way Valve

•

Solenoid Board

•

Blower/Fan Assembly (with Alarm Transducer)

Содержание Vmax Encore























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды