manualshive.com logo in svg

VIASYS Vmax Encore, Техническое справочное руководство

Поделиться
Скачать
VIASYS Vmax Encore Скачать руководство пользователя страница 20

Chapter 1 Introduction 

1–14

L2707

Technical Reference Manual

Vmax Encore

BAROMETRIC PRESSURE SENSOR

A barometric pressure sensor is located in the Analyzer Assembly to continuously measure 
ambient barometric pressure, making operator-entry of a reading from a barometer unnecessary. 
This same sensor also measures changes in gas sample line pressure so that adjustments in gas 
partial pressures can be calculated.

DIRECTION PRESSURE SENSOR

A direction pressure sensor is located in the Analyzer Assembly to determine the direction of the 
flow signal. This sensor provides for automatic detection of inspiratory and expiratory volumes.

MOUTH PRESSURE SENSOR

A mouth pressure sensor is located in the Analyzer Assembly to measure respiratory pressures at 
the mouth.

ANALOG I/O POD

An Analog I/O Pod is provided for interfacing external devices. The pod provides for the following 
device interfaces:

•

Eight analog input

•

Four analog output

•

Three TTL output

•

One analog heart rate input or SMC 3-Lead ECG input

Содержание Vmax Encore























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды