Deut
sch
Seite 12
S
UBAUDIO
-S
ETMODUS
(
P
ROGRAMMIERUNG
VON
CTCSS-F
REQUENZ
/
DCS-C
ODE
)
Bei Bedarf kann die CTCSS-Frequenz oder der DCS-Code, der für den Kanal gespeichert ist, geändert werden.
1. Funkgerät ausschalten, indem der
VOL/PWR
-Knopf
entgegengesetzt dem Uhrzeigersinn an den Anschlag
gedreht wird, bis er mit einem Klick einrastet.
2. Um in den Subaudio-Setmodus zu gelangen, das
Funkgerät bei gleichzeitig gedrückter
PTT
und Taste
[
SIDE 1
] einschalten. Die Tonfolge „Tone A” (s. S.
14) ist hörbar. Solange das Funkgerät im Subaudio-
Setmodus ist, leuchtet die LED gelb.
3. Mit dem Kanalwahlknopf den Kanal einstellen, für den
die Subaudio-Einstellung geändert werden soll.
4.
PTT
drücken, um den Kanal zu bestätigen. Tonfolge
„Tone B” ist hörbar.
Wenn der Kanal frei ist, hört man die Fehler-Tonfolge
„Tone C”.
5. Mit dem Kanalwahlknopf die LSB-Stelle der 1. Spalte
in der Tone Table (s. S. 13) einstellen.
Ch1=1, Ch2=2, ............. Ch9=9, Ch10=0
Wenn die Einstellung der bereits voreingestellten
entspricht, hört man die Tonfolge „Tone G”.
6.
PTT
drücken, um die Einstellung zu bestätigen.
Tonfolge „Tone D” ist hörbar.
Wenn „Ch11” bis „Ch16” eingestellt wurde, sind
CTCSS und DCS abgeschaltet. Die Tonfolge „Tone
F” ist hörbar und die Subaudio-Einstellung für den
aktuellen Kanal wird beendet. Falls in diesem Fall die
Subaudio-Einstellung für einen weiteren Kanal
verändert werden soll, ist Schritt 3 zu wiederholen.
7. Mit dem Kanalwahlknopf die MSB-Stelle (100er- und
10er-Stelle) der Ton-Tabelle einstellen.
Ch1=1, Ch2=2, ............. Ch9=9, Ch10=10,
Ch11=11, ............. Ch15=15, Ch16=16
Wenn die Einstellung der bereits voreingestellten
entspricht, hört man die Tonfolge „Tone G”.
8.
PTT
drücken, um die MSB-Einstellung zu bestätigen.
Tonfolge „Tone E” ist hörbar.
Die Einstellungen „164” bis „169” haben keine
Funktion. (Falls für den Kanal weder CTCSS noch
DCS benötigt werden, muss man dies beim LSB
einstellen (s. Punkt 6).
9.
PTT
drücken, um die Subaudio-Einstellung für den
aktuellen Kanal zu beenden. Tonfolge „Tone E” ist
hörbar.
10. Die Subaudio-Einstellung für den aktuellen Kanal ist
damit abgeschlossen. Falls weitere Einstellungen
gewünscht sind, die Schritte 3 bis 8 wiederholen.
11. Um in den Subaudio-Setmodus zu verlassen, das
Funkgerät ausschalten oder die Tasten [
SIDE 1
] oder
[
SIDE 2
] drücken.
12. Wenn das Funkgerät wieder eingeschaltet wird, ertönt
die Tonfolge „Tone H”.
Содержание VX-351-EG3J-1
