Vertex Standard VX-150 Скачать руководство пользователя | Manualshive

Страница: 43 / 44

background image

Specifications

41

GENERAL

Frequency coverage (MHz):

144 to 147.995 (version A)
144 to 145.995 (version B)

Channel steps:

5, 10, 12.5, 15, 20, 25 & 50 kHz

Standard repeater shift:

600 kHz

Emission type:

G3E

Supply voltage:

6.0 to 16.0 VDC

Current consumption:

Receive: 130 mA;
Transmit (HIGH:5W) : 1.3 A;

(MID:2 W) : 800 mA;
(LOW:0.5 W) : 500 mA;

Auto Power Off : 8 mA

Antenna (BNC jack):

YHA-62 rubber flex antenna

Case size (WHD):

58 (W) x 108.5 (H) x 26.5 (D) mm (w/o knob & antenna)

Weight (approx.):

325g w/FNB-64 & antenna

RECEIVER

Circuit type:

Double-conversion superheterodyne

Sensitivity (for 12dB SINAD): better than 0.16µV
Adjacent channel selectivity: better than 70 dB
Intermodulation:

better than 70 dB

Audio output:

0.4 W @8 ohms for 10% THD (@7.2V)

TRANSMITTER

Power output:

5 W (@ 7.2 V & 13.8 V EXT DC IN)

Frequency stability:

better than ±5 ppm

Modulation system:

variable reactance

Maximum deviation:

±5 kHz

Spurious emissions:

better than 60 dB below carrier

Audio distortion (@ 1 kHz):

less than 5 %, w/3 kHz deviation

Microphone type:

2-kilohm condenser

Burst tone:

1750 Hz (except version A)

Specifications may be subject to change without notice or obligation.

1. Changes or modifications to this device not expressly approved by Yaesu Musen could void

the user’s authorization to operate this device.

2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions; (1) this device may not cause harmful interference, and (2) this device must accept
any interference including interference that may cause undesired operation.

3. The scanning receiver in this equipment is incapable of tuning, or readily being altered, by the

User to operate within the frequency bands allocated to the Domestic public Cellular
Telecommunications Service in Part 22.

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two
conditions; (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesirable operation of the device.

«
...
41
42
43
44
»

Содержание VX-150













































Отзывы:

Нет отзывов

Похожие инструкции для VX-150

Бренд: Harman Kardon Страницы: 4

Бренд: Harman Kardon Страницы: 4

Бренд: Harman Kardon Страницы: 11

Бренд: Harman Kardon Страницы: 48

Бренд: Harman Kardon Страницы: 118

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 10

Бренд: Harman Kardon Страницы: 52

Бренд: JCM Technologies Страницы: 3

Бренд: Watkins Johnson Страницы: 9

Бренд: YouKits Страницы: 1

Бренд: Sennheiser Страницы: 32

THERMASGARD ALTM 2-VA

Бренд: S+S Regeltechnik Страницы: 16

AIR-EAGLE FM2 43-1000-SSB-R1/8-DC

Бренд: BWI Eagle Страницы: 2

FT-FOTR-1V-ST-S

Бренд: Fiber Tronix Страницы: 4

AIR-EAGLE XLT 44P-8-ESTOP

Бренд: BWI Eagle Страницы: 3

Бренд: EI Страницы: 41

Бренд: Aqua Quip Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды