manualshive.com logo in svg

VersaLogic Lion, Справочник по аппаратуре

Поделиться
Скачать
VersaLogic Lion Скачать руководство пользователя страница 35

Interfaces and Connectors 

Lion (VL-EPMe-42) Reference Manual 

28 

The VersaLogic VL-CBR-2402 cable is a USB 3.0 Type-C to Type-A socket adapter. The VL-
CBR-2402 cable can be used to connect the Lion to any certified USB 3.0 hubs. 

LEDs 

FPGA Controlled LEDs 

The FPGA controls three LEDs (the Blue is an individual LED and the Green/Yellow is a dual-
package): 

 

Blue – used for SATA (and mSATA) activity indication.  

 

Green – used for Power-Good indication when in S0 (and will do a very low duty cycle 
pulse when in sleep modes as an indication that the board is still powered). 

 

Yellow – used for errors or debug (software enables this).  

The Yellow LED can be also used for debug purposes. 

Power LEDs 

The power LED on the VL-CBR-4005 indicates that the paddleboard is being powered by the 3.3 
V supply (though it does not indicate that all S0 power supplies are within specified limits). The 
LED is lit only when the board is in the S0 power state. If the board enters a Sleep or Hibernate 
mode, the LED will not be lit.  

Power Button 

Connector J13 includes an input for a power button. Shorting J13 (pin 17) to ground causes the 
board to enter an S5 power state (similar to the Windows Shutdown state). Shorting it again 
returns the board to the S0 power state and reboots the board. The button can be configured in 
Windows to enter an S3 power state (Sleep, Standby, or Suspend-to-RAM), an S4 power state 
(Hibernate or Suspend-to-Disk), or an S5 power state (Shutdown or Soft-Off).  

The input can be connected to ground using the normally open contacts of a pushbutton switch or 
a relay, or with a switching transistor (open-collector or open-drain) capable of sinking 1 mA. The 
input must be driven to a voltage between 0 V and 500 mV to be recognized by the Lion. Do not 
add an external pull-up resistor to this signal. 

This connector uses IEC 61000-4-2-rated TVS components to help protect against ESD damage. 

In configurations where a power button is not connected to the board, if the system is put into an 
S5 state, power can be restored by turning off the power supply and turning it back on. This 
behavior is set by default in the BIOS. 

Содержание Lion

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды