Vermont Castings RFSDV34 Скачать руководство пользователя

Страница: 1 / 36

RFSDV_24_34_line

1_3550

rev. 0602 rjs

Installation Instructions and

Homeowner’s Manual

10003550 1/13 Rev. 13

DO NOT STORE OR USE GASOLINE

OR OTHER FLAMMABLE VAPORS

AND LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER

APPLIANCE.

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electric switch;

do not use any phone in your

building.

•

Immediately call your gas supplier

from your neighbor’s phone. Follow

the gas suppliers instructions.

•

If you cannot reach your gas

supplier call the fire department.

WARNING!

IF THE INFORMATION IN THIS

MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR

EXPLOSION MAY RESULT

CAUSING PROPERTY

DAMAGE, PERSONAL INJURY

OR LOSS OF LIFE.

PLEASE READ THIS MANUAL

BEFORE INSTALLING AND USING

APPLIANCE

INSTALLER/CONSUMER

SAFETY INFORMATION

FOR YOUR SAFETY

Installation and service must

be performed by a qualified

installer, service agency or the

gas supplier.

Freestanding

Direct Vent Gas Stove

with the LexFire Burn System™

Model: RFSDV34

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Содержание RFSDV34





































Результаты поиска

Содержание RFSDV34

Отзывы:

Похожие инструкции для RFSDV34

Бренды по названию

Популярные бренды

Vermont Castings RFSDV34, Инструкции по установке и руководство для владельца

Результаты поиска

Содержание RFSDV34

Отзывы:

Похожие инструкции для RFSDV34

Бренды по названию

Популярные бренды