manualshive.com logo in svg

Vermont Castings 36CDVZRRN, Инструкции по установке и руководство для владельца, Страница: 33 / 44

Поделиться
Скачать
Vermont Castings 36CDVZRRN Скачать руководство пользователя страница 33

33

CDVZ Series Direct Vent Gas Fireplace

20014621

The conversion of this appliance from one gas 

to another must be carried out by an authorized 

service provider.

1.  Disconnect power to the unit and shut off the gas sup-

ply.

2.  Remove window frame assembly.
3.  Remove the lava rock and ember material. (Fig. 67)

Fuel Conversion Instructions

#/
REMOVEEMBERSROCK
REARSCREWS

Front Log

Lava Rock

Ember 

Material

CO134

Fig. 67

  Remove lava rock and ember material.

4.  Push the log support towards the back of the fireplace 

and lift out the front log mounting assembly. (Fig. 68)

5.  Remove the two (2) screws securing the rear log to the 

back of the firebox. Remove the three (3) screws secur-

ing the rear log support to the back of the firebox. (Fig. 

69)

#/
REMOVEREARLOG
FRONTLOGSUPPORT

Remove 

Screws

Log Support & Front Log

CO135

Fig. 68

  Remove rear log and log support and front log.

&#
REMOVEBURNERTUBE
DJT

Rear Log 

Support

Remove 

Screws

Burner Tube

Remove Screws

Pilot Assembly

FC114

Fig. 69

  Remove burner tube and rear log support.

&#
BRASSELBOW
DJT

Orifice

Brass Elbow

FC111

Fig. 70

  Remove orifice from brass elbow.

&#
AIRSHUTTER
DJT

Air Shutter Adjustment 

Screw

LP: Fully Open

NG: 1/8” Open

FC112

Fig. 71

  Adjust air shutter.

8.  Install the new conversion orifice.
9.  Loosen the adjusting screw that holds the air shutter to 

the burner tube. Adjust air shutter to:

  LP - fully open; NG - 1/8” open.  (Fig. 71)
10. Install the burner tube and secure with the two (2) screws 

removed earlier.

11.  Burner orifice installation complete.

Pilot Conversion
NOTE:

  It  is  not  necessary  to  remove  the  pilot  tube  for 

conversion.
1.  Remove pilot hood by lifting up. (Fig. 72)
2.  Remove  pilot  orifice  with  the  appropriate  size Allen 

wrench. (Fig. 73)

3.  Install conversion pilot orifice.
4.  Reinstall pilot hood. Be sure to align pilot hood with index 

tab.

Pilot conversion installation is complete.

The procedure for converting from one gas to 

another is the same regardless of the initial gas 

used. The only variation is in the orifice sizes 

and component part numbers. Your authorized 

service provider will ensure the correct parts 

are used.

6.  Remove the two (2) screws securing the burner tube to 

the burner pan. (Fig. 69)

7.  Remove the orifice from the brass elbow. Use a 9/16” 

open end wrench to hold the elbow while using the 1/2” 

wrench to remove the orifice. (Fig. 70)

Содержание 36CDVZRRN













































Отзывы:

Нет отзывов