Veichi AC300 Series, Техническое руководство

Страница: 87 / 95

AC300 Series Vector Control Inverter Manual Function Parameter Table
170
F11.07 PID control selection
LED”0” digit: Feedback feature
selection
0: Positive feature 1:Negative
feature
LED”00”/”000” digit: Reserved
LED”0000” digit: Differential
adjustment properties
0: Differential bias
1: Differential of feedback
0100 ● 0xB07
F11.08 PID preset output 0.0
～
100.0% 100.0% ● 0xB08
F11.09
PID preset output
running time
0.0
～
6500.0s 0.0s ● 0xB09
F11.10
PID control deviation
0.0 ～ 100.0% 0.0% ● 0xB0A
F11.11 Proportional gain P1 0.000
～
8.000 0.100 ● 0xB0B
F11.12 Integral time I1 0.0
～
600.0s 1.0s ● 0xB0C
F11.13 Differential time D1 0.000 ～ 6.000s 0.000s ● 0xB0D
F11.14 Proportional gain P2 0.000
～
8.000 0.100 ● 0xB0E
F11.15 Integral time I2 0.0
～
600.0s 1.0s ● 0xB0F
F11.16 Differential gain D2 0.000 ～ 6.000s 0.000s ● 0xB10
F11.17
PID Parameter
switching condition
0: No switch
1: Use DI terminal to switch
2: Switch according to deviation
0 ● 0xB11
F11.18
Low value of
switching deviation
0.0 ～ 100.0% 20.0% ● 0xB12
F11.19
High value of
switching deviation
0.0 ～ 100.0% 80.0% ● 0xB13
F11.20 Reserved 0xB14
F11.21 Differential limit 0.0 ～ 100.0% 5.0% ● 0xB15
F11.22 PID output upper limit 0.0
～
100.0% 100.0% ● 0xB16
F11.23 PID output lower limit -100.0
～
F11.19 0.0% ● 0xB17
F11.24 PID output filter time 0.000 ～ 6.000s 0.000s ● 0xB18
F11.25
Feedback wire break
detection time
0.0
～
120.0s 1.0s ● 0xB19
F11.26
Feedback wire break
action selection
0: Go on PID operation without alarm
1: Stop and alarm malfunction
2: continue to PID operation and
output alarm signal
3: Run at the current frequency and
output alarm signal
0 ● 0xB1A
F11.27
Wire break alarm
0.0 ～ 100.0% 100.0% ● 0xB1B
F11.28 Wire break alarm 0.0
～
100.0% 0.0% ● 0xB1C
F11.29
Close-loop suspend
detection threshold
0.0 ～ 100.0% 0.0% ● 0xB1D
F11.30
Close-loop suspend
detection time
0.0 ～ 600.0s 1.0s ● 0xB1E
AC300 Series Vector Control Inverter Manual Function Parameter Table
171
Multi-Speed and PLC Function Parameter Group
NO. Function description Range of setting and definition
Factory
default
Feature Address
F12.00 PLC Speed 1 0.00 ～ Max frequency 10.00Hz ● 0xC00
F12.01 PLC Speed 2 0.00
～
Max frequency 20.00Hz ● 0xC01
F12.02 PLC Speed 3 0.00
～
Max frequency 30.00Hz ● 0xC02
F12.03 PLC Speed 4 0.00 ～ Max frequency 40.00Hz ● 0xC03
F12.04 PLC Speed 5 0.00
～
Max frequency 50.00Hz ● 0xC04
F12.05 PLC Speed 6 0.00
～
Max frequency 40.00Hz ● 0xC05
F12.06 PLC Speed 7 0.00 ～ Max frequency 30.00Hz ● 0xC06
F12.23 PLC Speed 8 0.00
～
Max frequency 20.00Hz ● 0xC07
F12.08 PLC Speed 9 0.00 ～ Max frequency 10.00Hz ● 0xC08
F12.09 PLC Speed 10 0.00
～
Max frequency 20.00Hz ● 0xC09
F12.10 PLC Speed 11 0.00
～
Max frequency 30.00Hz ● 0xC0A
F12.11 PLC Speed 12 0.00 ～ Max frequency 40.00Hz ● 0xC0B
F12.12 PLC Speed 13 0.00
～
Max frequency 50.00Hz ● 0xC0C
F12.13 PLC Speed 14 0.00
～
Max frequency 40.00Hz ● 0xC0D
F12.14 PLC Speed 15 0.00 ～ Max frequency 30.00Hz ● 0xC0E
F12.15
PLC Running mode
selection
LED”0” digit: cycle mode
0: Stop after single cycle
1: Continuous cycles
2: Keep final value after single cycle
LED”00” digit: Time unit
0: second 1: minute
2:hour
LED”000” digit: Power down
memory
0: Not save 1: save
LED”0000” digit: Start mode
0: Restart from the 1st stage
1: Restart from the stop stage
2: Continue running from the time
when stop
0000 ● 0xC0F
F12.16 PLC 1st step running 0.0
～
6500.0(s/m/h) 10.0 ● 0xC10
F12.17 PLC 2nd step running 0.0
～
6500.0(s/m/h) 10.0 ● 0xC11
F12.18 PLC 3rd step running 0.0
～
6500.0(s/m/h) 10.0 ● 0xC12
F12.19 PLC 4thstep running time 0.0
～
6500.0(s/m/h) 10.0 ● 0xC13
F12.20
PLC 5th step running
0.0 ～ 6500.0(s/m/h) 10.0 ● 0xC14
F12.21 PLC 6th step running 0.0
～
6500.0(s/m/h) 10.0 ● 0xC15
F12.22 PLC 7th step running 0.0
～
6500.0(s/m/h) 10.0 ● 0xC16
F12.23
PLC 8th step running
0.0 ～ 6500.0(s/m/h) 10.0 ● 0xC17
F12.24 PLC 9th step running 0.0
～
6500.0(s/m/h) 10.0 ● 0xC18
F12.25
PLC 10th step running
0.0 ～ 6500.0(s/m/h) 10.0 ● 0xC19
F12.26 PLC 11th step running 0.0 ～ 6500.0(s/m/h) 10.0 ● 0xC1A