background image

59

9 Diagnosis, asset management and service

VEGAPULS 67 • 4 … 20 mA/HART - four-wire

36532-EN-160224

• 

PC with PACTware/DTM 

• 

Control system with EDD 

• 

Display and adjustment module

Further echo curves:

 Up to 10 echo curves can be stored in a ring 

buffer in this memory section. Further echo curves are stored via:

• 

PC with PACTware/DTM 

• 

Control system with EDD 

9.3  Asset Management function

The instrument features self-monitoring and diagnostics according to 

NE 107 and VDI/VDE 2650. In addition to the status messages in the 

following tables, detailed error messages are available under menu 

item "

Diagnostics

" via the display and adjustment module, PACTware/

DTM and EDD.

The status messages are divided into the following categories:

• 

Failure

• 

Function check

• 

Out of specification

• 

Maintenance requirement

and explained by pictographs:

4

1

2

3

Fig. 36: Pictographs of the status messages
1  Failure - red

2  Out of specification - yellow

3  Function check - orange

4  Maintenance - blue

Failure:

 Due to a malfunction in the instrument, a failure message is 

outputted.
This status message is always active. It cannot be deactivated by the 

user.

Function check:

 The instrument is in operation, the measured value 

is temporarily invalid (for example during simulation).
This status message is inactive by default. It can be activated by the 

user via PACTware/DTM or EDD.

Out of specification:

 The measured value is unstable because the 

instrument specification is exceeded (e.g. electronics temperature).

This status message is inactive by default. It can be activated by the 

user via PACTware/DTM or EDD.

Maintenance:

 Due to external influences, the instrument function 

is limited. The measurement is affected, but the measured value is 

Status messages

Содержание VEGAPULS 63





















































































Отзывы: