Vega VEGAPULS 63 страница 4 Скачать руководство пользователя

Страница: 4 / 84

1 About this document

VEGAPULS 67 • 4 … 20 mA/HART - four-wire

36532-EN-160224

1 About this document

1.1 Function

This operating instructions manual provides all the information you

need for mounting, connection and setup as well as important instruc-

tions for maintenance and fault rectification. Please read this informa

tion before putting the instrument into operation and keep this manual

accessible in the immediate vicinity of the device.

1.2 Target group

This operating instructions manual is directed to trained specialist

personnel. The contents of this manual should be made available to

these personnel and put into practice by them.

1.3 Symbols used

Information, tip, note

This symbol indicates helpful additional information.

Caution:

If this warning is ignored, faults or malfunctions can result.

Warning:

If this warning is ignored, injury to persons and/or serious

damage to the instrument can result.

Danger:

If this warning is ignored, serious injury to persons and/or

destruction of the instrument can result.

Ex applications

This symbol indicates special instructions for Ex applications.

•

List

The dot set in front indicates a list with no implied sequence.

→

Action

This arrow indicates a single action.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.

Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

Содержание VEGAPULS 63





















































































Результаты поиска

Содержание VEGAPULS 63

Отзывы:

Похожие инструкции для VEGAPULS 63

Бренды по названию

Популярные бренды

Vega VEGAPULS 63, Руководство по эксплуатации

Результаты поиска

Содержание VEGAPULS 63

Отзывы:

Похожие инструкции для VEGAPULS 63

Бренды по названию

Популярные бренды