Vega VEGAPULS 63 страница 11 Скачать руководство пользователя

Страница: 11 / 84

3 Product description

VEGAPULS 67 • 4 … 20 mA/HART - four-wire

36532-EN-160224

You can find further information in the operating instructions "

VE-

GADIS 82

" (Document-ID 45300).

PLICSMOBILE T61 is an external GSM/GPRS radio unit for transmis-

sion of measured values and for remote parameter adjustment of

plics

sensors. Adjustment is carried out via PACTware/DTM and the

integrated USB connection.

You can find further information in the supplementary instructions

PLICSMOBILE T61

" (Document-ID 37700).

The protective cover protects the sensor housing against soiling and

intense heat from solar radiation.

You will find additional information in the supplementary instructions

manual "

Protective cover

" (Document-ID 34296).

Electronics module "VEGAPULS series 60" is a replacement part for

radar sensors of VEGAPULS series 60. A different version is available

for each type of signal output.

You can find further information in the operating instructions "

Elec-

tronics module VEGAPULS series 60

" (Document-ID 36801).

The supplementary electronics is a replacement part for the following

sensors with 4 … 20 mA/HART - two-wire:

•

VEGAPULS series 60

•

VEGAFLEX 80 series

•

VEGABAR series 80

You can find further information in the operating instructions "

Supple-

mentary electronics for 4 … 20 mA/HART - four-wire

" (Document-ID

42766).

PLICSMOBILE T61

Protective cap

Electronics module

Supplementary electron-

ics 4 … 20 mA/HART -

four-wire

Содержание VEGAPULS 63





















































































Результаты поиска

Содержание VEGAPULS 63

Отзывы:

Похожие инструкции для VEGAPULS 63

Бренды по названию

Популярные бренды

Vega VEGAPULS 63, Руководство по эксплуатации

Результаты поиска

Содержание VEGAPULS 63

Отзывы:

Похожие инструкции для VEGAPULS 63

Бренды по названию

Популярные бренды