Vega VEGAPULS 63 Скачать руководство пользователя

Страница: 53 / 84

6 Set up with the display and adjustment module

VEGAPULS 67 • 4 … 20 mA/HART - four-wire

36532-EN-160224

6.5 Saving the parameter adjustment data

We recommended noting the adjusted data, e.g. in this operating

instructions manual, and archiving them afterwards. They are thus

available for multiple use or service purposes.

If the instrument is equipped with a display and adjustment module,

the data in the sensor can be saved in the display and adjustment

module. The procedure is described in the menu "

Additional adjust-

ments

" in the menu item "

Copy sensor data

". The data remain there

permanently even if the sensor power supply fails.
The following data or settings for adjustment of the display and ad-

justment module are saved:

•

All data of the menu "

Setup

" and "

Display

•

In the menu "

Additional settings

" the items "

Sensor-specific units,

temperature unit and linearization

•

The values of the user programmable linearization curve

The function can also be used to transfer settings from one instru-

ment to another instrument of the same type. If it is necessary to

exchange a sensor, the display and adjustment module is inserted

into the replacement instrument and the data are likewise written into

the sensor via the menu item "

Copy sensor data

Backup on paper

Backup in the display and

adjustment module

Содержание VEGAPULS 63





















































































Результаты поиска

Содержание VEGAPULS 63

Отзывы:

Похожие инструкции для VEGAPULS 63

Бренды по названию

Популярные бренды

Vega VEGAPULS 63, Руководство по эксплуатации

Результаты поиска

Содержание VEGAPULS 63

Отзывы:

Похожие инструкции для VEGAPULS 63

Бренды по названию

Популярные бренды