Vectra Fitness Genisys 2761 Скачать руководство пользователя

Страница: 147 / 158

Vectra Genisys® Therapy System

138

OPTiON OPErATiON

When charging Battery Module, make

certain the System is electrically grounded

by connecting only to a grounded

electrical service receptacle conforming to

the applicable national and local electrical

codes . Using any other power source

will cause extensive damage to internal

components and render the System

unsafe for patient therapy .

ChArgiNg BATTErY MOduLE

Use the following instructions to properly

charge the Genisys Battery Module for use .

With Battery Module installed on the Vectra

Genisys Therapy System, plug the System

into an approved, grounded power outlet .
Turn the System on . The Lightning Bolt

icon will display indicating the battery

is charging . As the battery charges, the

Battery indicator icon will progressively fill

until it is solid black indicating full charge .

baTTEry

InDIcaTOr

IcOn

Charge the battery according to the

•

instructions found in this manual .

Never attempt to charge the battery

on any other charging mechanism .
Use the Battery Module only with the

•

Vectra Genisys Therapy System .
Do not reverse the polarity of the

•

Battery Module . Doing so can increase

the individual cell temperature and

cause cell rupture or leakage .

lIGhTnInG

bOlT IcOn

Charging efficiency is optimum within a

•

temperature range of 50 °F to 86 °F (10

°C to 30 °C) . Charge the Battery Module

within this temperature range .
At temperatures below 32 °F (0 °C) the

•

gas absorption reaction is not sufficient

and causes an increase of the gas

pressure inside the battery . This condition

can activate the safety vent and lead

to alkaline gas leaking and battery

performance deterioration .
Charging efficiency of the Battery Module

•

drops at temperatures above 104 °F

(40 °C) and can disrupt full charging,

lead to deterioration in performance and

battery cell leakage .

Charging of the Battery Module is required

when the Battery Indicator begins flashing .

When to Recharge

NOTE:

The Lightening Bolt icon will

continue to display as long as

the System is connected to

a power source .

Charging Temperature

Содержание Genisys 2761































































































































































Результаты поиска

Содержание Genisys 2761

Отзывы:

Похожие инструкции для Genisys 2761

Бренды по названию

Популярные бренды

Vectra Fitness Genisys 2761, Руководство пользователя

Результаты поиска

Содержание Genisys 2761

Отзывы:

Похожие инструкции для Genisys 2761

Бренды по названию

Популярные бренды