Vectra Fitness Genisys 2761 Скачать руководство пользователя

Страница: 154 / 158

Vectra Genisys® Therapy System

145

TrOuBLEShOOTiNg

ErrOr COdES (CONTiNuEd)

code

number

Type

Message

Probable cause

Possible remedies

144

Warning

Wrong Laser Applicator connected to system for the protocol

selected.

Connect correct Laser Applicator to the system.

If Applicator is connected, reset Therapy System by turning main power switch Off and On.

Connect a known good Laser Applicator.

If problem continues, send Laser Module to Factory for service.

145

Warning

Patient Data Card button on Home screen was pressed with no

Patient Data Card installed into system port and no treatment

currently being performed.

Properly insert a Patient Data Card, set up and perform the treatment and save data to Patient

Data Card.

In the event that an Error message or Warning appears beginning with

a 2 or 3, immediately stop all use of the system and contact the dealer

or DJO, LLC for service . Errors and Warnings in these categories indicate

an internal problem with the system that must be tested by DJO, LLC

or a Field Service Technician certified by DJO, LLC before any further

operation or use of the system

Use of a system that indicates an Error or Warning in these categories

may pose a risk of injury to the patient, user, or extensive internal

damage to the system .

Содержание Genisys 2761































































































































































Результаты поиска

Содержание Genisys 2761

Отзывы:

Похожие инструкции для Genisys 2761

Бренды по названию

Популярные бренды

Vectra Fitness Genisys 2761, Руководство пользователя

Результаты поиска

Содержание Genisys 2761

Отзывы:

Похожие инструкции для Genisys 2761

Бренды по названию

Популярные бренды