Vectra Fitness Genisys 2761 Скачать руководство пользователя страница 127

Страница: 127 / 158

Vectra Genisys® Therapy System

118

iNSTALLATiON/rEMOvAL

Remove the Therapy System from the

Therapy System Cart, if equipped . Refer

pages 131 through 133

for proper

instructions .
Place Therapy System face down on a clean

working surface protected with a soft, clean

fabric to prevent damage to the lens .

iNSTALLATiON- ChANNEL 3/4 ELECTrOThErAPY, NiMh BATTErY ANd LASEr MOduLE (CONTiNuEd)

Disconnect Mains Power

Disconnect the system from the

power source (outlet or remove battery

module if installed) before attempting

any maintenance, installation, removal or

replacement procedures to prevent electrical

shock and possible damage to system .

Disconnect the Mains Power Cord from

the power supply . Remove the Rear Access

Panel and disconnect the Mains Power

Cord from the Therapy System .

rEar

accESS

PanEl

MaInS

POwEr

cOrD

Remove Therapy System from Cart

NOTE:

Do not remove the sEMG

Module, if installed . The

sEMG Module will not

interfere with installation

of the Channel 3/4 Electrotherapy

Module .

Remove the Front Access Cover and

disconnect the Lead Wires and Accessories

from the Therapy System .

Remove Lead Wires and Accessories

rEMOvE lEaD

wIrES anD

accESSOrIES

EMG

MODulE

lanyarD

Содержание Genisys 2761































































































































































Результаты поиска

Содержание Genisys 2761

Отзывы:

Бренды по названию

Популярные бренды

Vectra Fitness Genisys 2761, Руководство пользователя

Результаты поиска

Содержание Genisys 2761

Отзывы:

Бренды по названию

Популярные бренды