background image

PHONE PAIRING – 

the first step in using the kit is 

to register your Bluetooth™ enabled phone with the 

VControl

. This process usually called “pairing” or 

“registration” allows your phone to communicate 
with the hands-free system and ensures that other 
phones cannot inadvertently do so. 

 

 

13

 
Please follow the steps below to complete this 
process: 
 

 

Turn on your cellular telephone and ensure 
that it is Bluetooth-enabled and supports 
Hands-free profile. 

 

Turn on your vehicle ignition and after a few 
seconds, the Power LED on the control pad 
should light briefly and then go out 
[signifies the system is active and ready to 
use].  This will take a few seconds. 

 

You now need to enter the set-up mode to 
register your phone; however, it is 
recommended that you follow the directions 
for your particular phone and turn the 
Bluetooth Power “On”. 

 

 “

Ready” 

<Beep> 

Set-up 

Î

 “

Phone Pairing, Confirmation 

Prompts, Changing Languages” 

Phone Pairing

 

Î

 “

Please select one of the 

following: Pair or Delete the current phone”

 

<Beep> 

Pair a Phone 

Î

 

“Please pair phone as 

mentioned in phone manual” 

<Beep> 

[Pair phone: Kit will remain silent for up to 2 
minutes]

 

 

 

The kit will wait for approximately 2 
minutes to have a Bluetooth™ enabled 
phone paired with it.  During this time the 
LED will be flashing.

 

 

Once the phone has found the kit, it will 
display a prompt on the phone.  It should 
display a message (on the phone) that is has 
located “Peiker HF”.  The kit will remain 
silent.  Continue to follow the phone’s 

pairing procedure until it asks you to enter a 
password.  Enter “0000” on the phone’s 
keypad and select the yes/dial key on the 
phone.  The phone will then complete the 
pairing process and should hear a prompt 
from the kit saying “

pairing completed

 

 

14 

 

You have now completed the registration 
process and the kit is ready to be used.  The 
LED on the Control Pad will remain on 
(green).

 

 

You only need to “Pair” your phone the first 
time you wish to use the kit.  With all 
subsequent uses, the phone will 
automatically connect to the kit.

 

 

You can pair up to 5 (five) phones with the 
Bluetooth™ kit.  Only one phone will be 
active (i.e. able to use the hands-free 
system) for calls at any one time.. The last 
connected phone will always have the 
highest priority when the unit tries to 
connect with a phone.  If the last connected 
phone is not available, then the kit will look 

for other phones stored in its memory (other 
phones that have been previously paired), in 
order of the original pairing process.  If you 
pair a sixth phone, then the phone that was 
first paired will be removed from the 
memory of the kit.

 

 
BASIC OPERATIONS 

 

After completing the registration process, your 
Bluetooth™ car kit is ready for everyday use.  The 
kit should operate properly each time you enter your 
vehicle, provided the initial requirements as defined 
below have occurred. 
 

Initial Requirements 
 

 

Ignition Switched On 

Î

 Your vehicle 

ignition must be switched on and the power 
LED on the kit constantly on.  It takes 
approximately 3 to 5 seconds after turning 
on your ignition for the kit to become active.

 

Содержание VControl



















Отзывы: