GEBRAUCHSANLEITUNG
8
87-900-854-01 (C)
FEHLERMELDUNGEN
In einigen Störungsfällen zeigt das Selbstdiagnoses-
system des Controllers die in der nachstehenden
Tabelle zusammengefaßten Meldungen an.
ANMERKUNG
Die Störungsmeldungen werden nur angezeigt, wenn
das Zubehör "handheld terminal" installiert ist.
MELDUNG
BESCHREIBUNG
BEHEBUNG
CHECK CONNECTION TO
PUMP
Fehlfunktion der Pumpen-Controller Ver-
bindung.
Sicherstellen, daß das Verbindungs-kabel
zwischen Pumpe und Controller an beiden
Seiten korrekt befestigt ist und keine
Unterbrechung vorliegt. Die Pumpe durch
zweimalige Betätigung der START-Taste
neustarten.
PUMP WAITING
INTERLOCK
Das Interlock-Signal auf dem Verbinder
P1 ist wegen der Kurzschlußunter-
brechung zwischen Pin 3 und Pin 8 des
Verbinders K1 oder wegen der Öffnung
des externen Interlock-Signals aktiv.
Den Kurzschluß zwischen Pin 3 und Pin 8
des Verbinders J1 rücksetzen oder das
externe Interlock-Signal schließen.
FAULT: OVERTIME SX
Beim Punpenstart im Modus "soft start"
hat die Pumpe die bei jedem Schritt
vorgesehene Geschwindigkeit inner-halb
von 15 Minuten nicht erreicht (X kann 0-
9
sein
und
zeigt
den
nicht
überwundenen Schritt an).
Sicherstellen, daß das System keine
Leckagen aufweist.
Die Pumpe durch zweimalige Betätigung
der START-Taste neustarten.
FAULT: PUMP OVERTEMP.
Die Temperatur des oberen Lagers bzw.
der Pumpe hat 60 °C überschritten.
Warten bis die Temperatur unter den
Schwellenwert gesunken ist. Die Pumpe
durch zweimalige Betätigung der START-
Taste neustarten.
FAULT: CONTROLLER
OVERTEMPERATURE
Die Temperatur des Controller-Trafos
hat 90 °C überschritten.
Warten bis die Temperatur unter den
Schwellenwert gesunken ist. Die Pumpe
durch zweimalige Betätigung der START-
Taste neustarten.
FAULT: TOO HIGH L0AD
Während des Normalbetriebs (nach der
Startphase)
ist
die
Pumpen
stromaufnahme
größer
als
die
vorgesehene (1,5 A).
Sicherstellen,, daß der Pumpenrotor
ungehindert drehen kann. Die Pumpe
durch zweimalige Betätigung der START-
Taste neustarten.
FAULT: SHORT CIRCUIT
Während des Normalbetriebs (nach der
Startphase) erfolgt ein Kurzschluß der
Ausgangsverbindung (Ausgangs-strom
größer als 2,2 A).
Die Verbindung zwischen Pumpe und
Controller prüfen. Die Pumpe durch
zweimalige Betätigung der START-Taste
neustarten.
SYSTEM OVERRIDE
Die Pumpe wurde durch ein von einem
entfernten
Kontakt
kommendes
Notsignal gestoppt.
Das Netzkabel des Controllers ausstecken
und die Störungsursache beheben. Das
Netzkabel wieder anschließen und die
Pumpe durch zweimalige Betätigung der
START-Taste neustarten.
OVERVOLTAGE
Defekt im Versorgungsbereich des
Controllers bzw. der Controller hat ein
falsches Signal erhalten.
Die Pumpe durch zweimalige Betätigung
der START-Taste neustar-ten. Erscheint
die Meldung wieder sollte der Varian-
Wartungs-dienst gerufen werden.