manualshive.com logo in svg

Varec 2920, Инструкция по установке и эксплуатации, Страница: 98 / 194

Поделиться
Скачать
Varec 2920 Скачать руководство пользователя страница 98

2920 Float & Tape Transmitter

5 Display and Configuration Interface

88

Installation and Operations Manual

Config Params

Response Delay

The default for the L&J response delay is 2 mS.

2nd TX Address

Set this Address between 1 and 127 to have the 
transmitter respond to a 2nd TankWay address. This 
Address must be different than the Unit Addr (Basic 
Setup) and the 3rd TX Address. Also, this address must 
be different than all other transmitters on the same L&J 
TankWay bus. The default value is 0 which means the 
transmitter will not respond.

2nd Level Ref

This is set if the transmitter needs to respond to the a 
second L&J TankWay address. This allows the 
transmitter to send additional data items.

If the 2nd TX Address is set, this selects the data item in 
the transmitter to be sent as the level portion of the L&J 
TankWay message. The Encoder Type (Basic Setup) 
determines the data range and resolution.

• 2000: 0 to 96 with a resolution of 0.01

• 1000/1500 Type 3: 0 to 255.9 with a resolution of 

0.02

• 1000/1500 Type 4: 0 to 170.66 with a resolution of 

0.003

2nd Temp Ref

This is set if the transmitter needs to respond to the a 
second L&J TankWay address. This allows the 
transmitter to send additional data items.

If the 2nd MS Address is set, this selects the data item in 
the transmitter to be sent as the temperature portion of 
the L&J TankWay message. This parameter is 
transmitted in the range -819.0 to 819.0 with 0.1 
resolution.

3rd TX Address

Set this Address between 1 and 127 to have the 
transmitter respond to a 3rd L&J TankWay address. This 
Address must be different than the Unit Addr (Basic 
Setup) and the 2nd TX Address. Also, this address must 
be different than all other transmitters on the same L&J 
TankWay bus. The default value is 0 which means the 
transmitter will not respond.

3rd Level Ref

If the 3rd TX Address is set, this selects the data item in 
the transmitter to be sent as the level portion of the L&J 
TankWay message. 

The Encoder Type (Basic Setup) 

determines the data range and resolution.

• 2000: 0 to 96 with a resolution of 0.01

• 1000/1500 Type 3: 0 to 255.9 with a resolution of 

0.02

• 1000/1500 Type 4: 0 to 170.66 with a resolution 

of 0.003

3rd Temp Ref

If the 3rd MS Address is set, this selects the data item in 
the transmitter to be sent as the temperature portion of 
the L&J TankWay message. This parameter is 
transmitted in the range -819.0 to 819.0 with 0.1 
resolution.

Содержание 2920



































































































































































































Отзывы:

Нет отзывов