Varec 2920 Скачать руководство пользователя страница 23

Страница: 23 / 194

Varec, Inc.

Chapter 3

Mounting

The 2920 FTT can be mounted in the following ways:

• Mount the complete transmitter on a 2500 ATG gaugehead (see “Mounting on a

Varec Gaugehead”).

• Mount the complete transmitter on a non-Varec gauge (see “Mounting on Alternate

Gaugeheads”).

• Mount standalone on a 2" pipe for gauging applications where the 2920 FTT

functions as a tank side integrator for HART level instrumentation (i.e., radar) as well
as spot temperature or HART average temperature.

This chapter describes each of the above procedures.

The tank can remain in-service and the mechanical float gauge can remain in place while
installing and configuring the 2920 FTT.

Note

Please read the safety guidelines section before beginning the mounting process.

Installation Safety Guidelines

• This equipment should be installed only by qualified personnel familiar with the

installation of tank gauging equipment.

• Caution should be exercised when entering any area that is posted or otherwise

assumed to contain hazardous gases. Always follow other local guidelines.

• Obtain a hot permit before removing the transmitter cover with power applied.
• To prevent shock hazards, the housing of all units should be properly grounded in

accordance with the National Electric Code. A grounding conductor should be wired
to the grounding terminal provided on the 2920 FTT.

• Refer to Chapter 2, Installation: "Correct Sealing of the Junction Box Covers" make

sure the o-ring is properly seated on the base of the cover.

Warning! Before attempting installation of the 2920 FTT, review the General Safety

Guidelines. Installation and maintenance personnel should become familiar with any

hazards present as well as any agency requirements before working with any equipment.

Mounting on a Varec Gaugehead

This procedure provides instructions to mount the transmitter on a 2500 ATG gaugehead.

Instructions applicable to other tank gauges follow in later paragraphs. To install the
gaugehead, refer to the

2500 Automatic Tank Gauge Installation and Operations Manual

. The

exploded view in that manual shows the mechanical relationship between this accessory and
the gaugehead.

Содержание 2920



































































































































































































Результаты поиска

Содержание 2920

Отзывы:

Varec 2920, Инструкция по установке и эксплуатации, Страница: 23 / 194

Результаты поиска

Содержание 2920

Отзывы: