Vanguard 54E100, Руководство оператора

Страница: 7 / 36

Not for
Reproduction
J. Finger Guard
K. Electric Starter
L. Starter Solenoid
M. Regulator/Rectifier
N. Carburetor - Carburetor Models
O. Carburetor Cover - Carburetor Models
P. Choke Control (if equipped) - Carburetor Models
Q. Breather/Breather Tube
R. Fuel Pump - EFI Models
S. Fuel Filter (if equipped)
T. Oxygen Sensor - EFI Models
U. Muffler (if equipped)
Engine Control Symbols and Meanings
Meaning Symbol Meaning Symbol
Engine speed - SLOW Engine speed - FAST
ON - OFF Engine speed - STOP
Engine start - Choke OPEN Engine start - Choke
CLOSED
Fuel Shut-off - CLOSED Fuel Cap
Fuel Shut-off - OPEN
Fuel level - Maximum
Do not overfill
Operation
Oil Recommendations
Oil Capacity: See the Specifications section.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers may have added oil to the engine. Before you start the engine for the first
time, make sure to check the oil level and add oil according to the instructions in this
manual. If you start the engine without oil, it will be damaged beyond repair and will not
be covered under warranty.
We recommend the use of Briggs & Stratton Warranty Certified oils for best performance.
Other high-quality detergent oils are acceptable if classified for service SF, SG, SH, SJ or
higher. Do not use special additives.
Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to
select the best viscosity for the outdoor temperature range expected. Engines on most
outdoor power equipment operate well with 5W-30 Synthetic oil. For equipment operated
in hot temperatures, Vanguard™ 15W-50 Synthetic oil provides the best protection.
SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting. A
10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil
consumption. Check oil level more frequently. B
5W-30 C
Synthetic 5W-30 D
Vanguard™ Synthetic 15W-50 E
Check Oil Level in Remote Oil Tank
See Figure: 5
Before adding or checking the oil
• Make sure the engine is level.
• Clean the oil fill area of any debris.
1. Clean oil fill area at top of remote tank.
2. Remove the dipstick (A, Figure 5) and wipe with a clean cloth.
3. Fully install the dipstick (A, Figure 5).
4. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 5) on the dipstick.
5. If oil level is low, open the oil fill cap (C, Figure 5).
6. Slowly add oil into the remote oil tank (D, Figure 5). Do not overfill. After adding oil,
recheck the oil level.
7. Fully install the dipstick (A, Figure 5).
8. Close the oil fill cap (C, Figure 5).
Low Oil Protection System (if equipped)
Some engines are equipped with a low oil sensor. If the oil is low, the sensor will either
activate a warning light or stop the engine. Stop the engine and follow these steps before
restarting the engine.
• Make sure the engine is level.
• Check the oil level. See the Check Oil Level section.
• If the oil level is low, add the proper amount of oil. Start the engine and make sure
the warning light (if equipped) is not activated.
• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton
Authorized Service Dealer to have the oil problem corrected.
Fuel Recommendations
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE Do not use unapproved gasolines, such as E15 and E85. Do not mix oil in
gasoline or modify the engine to run on alternate fuels. Use of unapproved fuels will
damage the engine components, which will not be covered under warranty.
To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See
Storage. All fuel is not the same. If starting or performance problems occur, change fuel
providers or change brands. This engine is certified to operate on gasoline. The emissions
control system for this engine is EM (Engine Modifications).
7