Van Der Stahl MS-350 NP Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

Van Der Stahl MS-350 NP Series Скачать руководство пользователя страница 26

MS-350 NP Operating Instructions Ver 4.02E

26

The sealing section consists of the parts as in the illustration below. When replacing parts, be careful to arrange the
parts exactly in the same order.

Daily maintenance or replacement of parts at an early stage can prevent the machine from being damaged, and
keeps the machine at the optimum condition. Replace parts according to the following directions in order to
maintain your machine in optimum operating condition.

10 Replacing the routine maintenance parts

Structure of the sealing section

Semi-transparent tape

Pressure lever

Silicone rubber (white)

W38mm glass tape

W40mm center-dry tape

Semi transparent tape

Sarcon sheet

Heating element

Temperature sensor

W38mm glass tape

Seal receiving plate

Always unplug the machine before maintenance.

Always use only specified parts sold through

Van der Stahl Scientific

.

WARNING

▪

Always unplug the power plug before replacing parts. There is a danger of electrocution if it has been

done

without unplugging.

▪

Follow the directions on this manual when replacing parts. Replacing parts in the way ignoring this manual

could cause malfunction of the machine as well as electrocution and fire.

▪

Always use only specified parts sold through

Van der Stahl Scientific

. Unspecified parts may cause

malfunction of

the machine.

«
...
24
25
26
27
28
...
»

Содержание MS-350 NP Series

















































Отзывы:

Нет отзывов