Valtra VALMET 6000 Скачать руководство пользователя

Страница: 71 / 1361

Model

Code

Page

21. Engine

1. 9. 1992

6000--8750

214

C. Fitting timing gear casing

The position of the timing gear casing and cover is deter-
mined by two tension pins. Therefore centring should not be

undertaken in connection with fitting. However, the tooth

backlash between the different gears should be checked.

Casing and covers that are delivered as spare parts also have

holes for the tension pins already machined.

1. Fit the casing with a new gasket against the cylinder block.

Drive in the tension pins with drift 9025 98700. Tighten bolts

and nuts.

2. Fit the injection pump together with gear wheel (if

removed).

3. Lubricate the camshaft bearings and insert the shaft in the

cylinder block. Release the pushrods and tappets if they have

been suspended.

4. Fit the idler gear with shaft stud and ensure that the mark-

ings are in the correct position. Fit the washer and tighten the

bolts to the correct torque.

5. Check the tooth backlash which should be

0,05---0,25 mm

Содержание VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды

Valtra VALMET 6000, Руководство по ремонту

Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды