Valtra VALMET 6000 Скачать руководство пользователя

Страница: 551 / 1361

154

Model

Code

Page

37. Autocontrol 5.2 (K41107---)

1. 8. 2000

371

6250--8950

1. 9. 2002

1. Autocontrol 5.2, general

Note!

AC 5.2 replaces the AC 5 system in 6250Hi---8950Hi

tractors from ser. no.

K41107

incl.

A. Additional functions in AC 5.2

a) Automatic traction control (Autotraction ON/

OFF)

See page

371/3

b) Fault codes

Fault codes have a fault code memory (in fault code mode

FI), in which can be checked and deleted from display. The

memory stores three latest fault codes and running hours of

the codes (control unit running hours).

New fault codes have been added in the system, see

pages

371/5

and

c) Automatic speed change of DPS

AutoDPS Auto2 function has been changes so that it func-

tions in fixed speed change revs and driver can set easily

the revs, see page

371/4

d) Speed Matching

When using the HiShift button the control unit adapts the

DPS speed so that it is suitable for driving situation when

the mechanical gear has been changed, see page

371/4

when traction is disengaged and re---engaged with clutch

pedal, with HiShift or with the shuttle lever.

e) Automatic calibrations

The automatic calibration is activated in setting mode FIII,

and it calibrates the initial pressures and pre---filling times of

the shuttle clutches, for DPS and PTO clutches only the

initial pressures, see page

371/11

. The calibrations can

also be done manually, see page

370/24D

. Manual calibra-

tion of PTO clutch, see page

371/12

f. Calibrations of clutch and gas pedals and

pedal position sensors

The activating point of the clutch pedal limit switch has

been changed to zero point of the pedal position. Now the

activating point of the switch is not necessary to adjust so

excatly as earlier.

The pedal calibrations have been changed so that the con-

trol unit accepts more unaccurate signal voltages for the

position sensors. Calibrations, see page

370/15

The position sensors are different and they have been fas-

tened so that no adjustment is needed, see pages

371/13

and

With the aid of the clutch pedal ratio index the pedal engag-

ing point can be adjusted separately in F--- and R---direc-

tions in the setting mode FIII, see page

371/10

g) Reverse drive controls (TwinTrac)

The reverse drive controls have separate digital inputs in

the control unit A1. The position of the seat (d14) deter-

mines which one of digital inputs the control unit uses.

h) Seat switch

The activating delay is normally 6 seconds, but 30 sec-

onds, if the clutch pedal has been depressed, see page

370/24

i) PTO start

The PTO start push buttons in the mudguards (option) have

separate digital inputs in the control unit. The PTO rocker

switch in the cab functions without delay and the push but-

ton in the mudguard has delay of 3 sec.

j) Zero--point offset of the shuttle outputs

(program versions 80...85)

Into the shuttle clutch, which is unpressurised, is fed an oil

pressure of 0,1...0,5 bar, so that no air can enter into the oil

passages. This happens if either of the driving directions is

engaged.

Note!

The pistons in the shuttle have been made smaller

and the spring force has been increased. The emptying

valve has been removed from the piston for reverse driving,

see page

440/19A

. In connection with this shuttle the AC

5.2 programs must always be used.

NOTE!

Initial pressures of the shuttle clutches have been

raised up to about 3,5 bar (earlier about 2 bar).

k) Other modifications

With the aid of output P7 the control unit switches on and

off the auxiliary relay K52 of the starter.

Control unit output P8 controls the 4WD automatics (relay

K27).

The control unit changes no more DPS speed in driving

speed of 65 km/h but gives only a fault code.

NOTE!

AC 5.2 has a new control unit, which can be used

also in the earlier manufactured tractors with AC 5, but a

different programs must be used.

AC 5.2 has only one main program there are several para-

meter files according to the tractor model and engine

power.

In the DPS---gear the spring force of clutch C3 has been

increased. Also oil way modifications have been done, see

page

440/15C

Parking brake!

A non---return valve from ser. no.

K50440

incl. has been fitted in the low pressure circuit, which to-

gether with program modification retards the pressure drop

in cases, in which engine stops during running ( e.g. fuel

runs out). A modification has been made in AC 5.2 pro-

gram, which disengages all multi---disc clutches if tractor’s

engine stops when the driving speed is over 5 km/h. In this

case the parking brake cylinder starts to brake after 15---30

seconds when the tractor has been already stopped.

The function of output DO5 has been changed inverse.

Earlier this output was parking brake on. Now parking

brake off. The control unit controls direct the valve and no

more via an auxiliary relay.

Содержание VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды

Valtra VALMET 6000, Руководство по ремонту

Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды