Valtra VALMET 6000 Скачать руководство пользователя

Страница: 1049 / 1361

992

Model

Code

Page

64. Powered front axle

1. 1. 1994

6000--8750

644

C. Changing differential gears/crown

wheel

Note!

Compare Op.

on page

644/1

1. Remove the differential unit from the axle housing, see

Op.

paragraphs

1---3

. Mark the halves of the differential carrier

to facilitate reassembling.

2. Unscrew the crown wheel bolts. Knock off the crown wheel.

3. Knock off the locating pins of the crown wheel. Open the

carrier and remove the various components.

4. Check the condition of the housing, differential gears and

bearing plates. Change all damaged parts. Lubricate all parts

with oil.

Note!

The differential pinion shaft is locked by means of the

locking pin. The diff. pinions thrust---washers are fitted so that

the locking lugs engage in the grooves on the differential

carrier.

5. Reassemble the differential and fit the carrier halves so that

the marks are in the same places as they were before dis-

mantling. Fit the crown wheel and tighten the screws to

Important!

If you change the crown wheel, also the pinion

shaft must be changed. Removing, fitting and adjusting the

pinion shaft, see page

644/3

instr.

and

6. Fit the locking pins. First the bigger pin and then the smaller

pin inside with the split pointing towards the heads of the

screws.

7. Fit the differential, see instr.

paragraphs

10---15

D. Changing differential bearings

Note!

If you change the differential bearings, the bearing

pre---load should be adjusted and also the tooth backlash

between the crown wheel and the pinion shaft should be

adjusted, see instr.

on page

644/5

1. Remove the differential, see instr.

paragraphs

1---3

2. Remove differential bearing outer races from both axle sec-

tions and remove any shims that may be fitted behind the

races.

3. Remove the roller bearings from the differential carrier.

4. Fit new bearings onto the differential carrier.

5. Press outer races against the bearings and use a vernier

caliper to measure the distance between them,

measure-

ment D

6. Read off

measurement A

(larger upper figure) marked

inside the longer axle housing. This is the distance between

the bottom of the differential bearing location and the axle

housing flange surface.

7. Read off

measurement B

marked inside the shorter axle

housing. This is the distance between the bottom of the bear-

ing housing and the axle housing flange surface.

8. The preload

(P)

of the differential bearings should be

0,05

. Calculate the number of shims required as follows:

S=(A+B)---D+P

9. Fit an equal number of shims under each differential bear-

ing.

10. Fit the differential into the axle housing and connect the

axle sections with several screws (

190 Nm

11. Measure the pinion/crown wheel tooth backlash using an

indicator gauge stylus against a screw on the drive flange. The

backlash should be in the range

0,20---0,25 mm

12. If the backlash is not correct transfer shims from one bear-

ing race to the other.

Note!

If the backlash is too small transfer shims from the

shorter axle section side to the longer side and vice versa.

13. When the backlash is correctly adjusted, fit the differential

unit and reassemble the axle housing, see instr.

paragraphs

10---15

«
...
1047
1048
1049
1050
1051
...
»

Содержание VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды

Valtra VALMET 6000, Руководство по ремонту

Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды