Valtra VALMET 6000 Скачать руководство пользователя

Страница: 280 / 1361

Picture 2.

Input and output signals to/from Delta Powershift

circuit card A10

+=energised, 0=unenergised

Z=18---pin connector seen from front

Pins 7 and 9 not in use

X23= Connector for extra buttons

GR1=Ground point in the rear part of the lever console

GR5=Ground point on the cab front wall

Note!

Position of various component and connectors and wiring

diagram are shown under code 310 alla.

DPS circuit card

INPUT signals

Pin 3:

Permanent earthing

Pin 4:

12 V via starter switch and fuse F22.

Pin 5:

12 V, when the foremost push button

is pressed. Otherwise 0 V.

Pin 6:

When the clutch pedal is in the upper

position, this pin has 12 V voltage.

When the pedal is depressed, the vol-

tage becomes 0.

Pin 10:

12V, when headlights are on, other-

wise 0 V.

Pin 11:

permanent current via fuse F11 (12 V)

Pin 12:

When the hand brake is applied, this

pin gets earth.

Pin 13:

Earthed, when engine is stopped

Pin 14:

12 V, when the rearmost push button

is depressed, otherwise 0 V.

Pins 15 and 16:

If the DPS ratio isdirect---overd-

rive---overdrive, the wire is con-

nected to pin 15. If the ratio is

reduction---direct---overdrive,

the wire is connected to pin 16

(wire is energised with 12 V).

OUTPUT signals

Pins 1 and 2:

Current to DPS solenoids (12 V). When the

clutch pedal is depressed, both pins are deenergised and

also the solenoid valves Y4 and Y6. When pin 1 is energised

(12 V), solenoid valve Y4 is energised. When pin 2 is live (12

V) solenoid valve Y6 is energised.

Pins 17, 18 and 8:

Signals to pilot lights (12 V).

Fault tracing of input signals

The input signals can be measured from the detached con-

nector of the circuit card, when the current is switched on.

When malfunctions occur, check the fuses, supply voltages

and earthing.

If one of input signals is uncorrect, check wiring and connec-

tors of this function and the sensor/switch in question.

Testing the circuit card buzzer

--- Ground pin 3 and feed voltage of 12 V to pin 11.

--- Ground pin 13 and feed voltage of 12 V to pin 4, at which

time the buzzer must give continuous signal. Disconnect

pin 4, after witch the buzzer should alarm about 2 min.

--- Remove ground from pin 13 and ground pin 12 and feed

a voltage of 12 V to pin 4, after which the buzzer should

give discontinuous sound signal.

--- Feed pin 10 with 12 V and disconnect pin 4, after which

the buzzer must give discontinuous alarm signal.

Fault tracing of output signals

Signals from pins 1 and 2 to solenoid valves can be verified by

engaging different ratios and by testing with a metal tool, whether

the solenoid valve in question becomes magnetic (see +/0 table)

and by measuring voltage in the solenoid valve connectors (12 V).

If there is no voltage at the solenoid valves, check connector X13

and wiring. If output signal from the circuit card A10 has no voltage,

although the input signals are OK, the whole circuit card should be

changed. The output signals can be measured with a multimeter

from circuit card connector while current is switced on and connec-

tor Z is in place. All outputs are 12 V. When measuring on the lower

pins, do not short circuit the pins. It is recommended, that the mea-

surements are carried out on the wire side of the connector

From pins 17, 18 and 8 signals are sent to the pilot lights. The pic-

ture above shows which pins are energised with different ratios.

The output signals (12 V) to the pilot lights can be measured on the

card with a multimeter, when current is switched on and connector

Z is in place. When the push buttons are pressed while the current

is switched on, the pilot lights must come on and go out in correct

order.

Position of connectors

X1:

In fuse box

X4:

In fuse box

X6:

In fuse box

X11:

Connector in the cab roof

X13:

Solenoid valve connector under the hand brake console

X19:

Plug on the cab front wall on the RH side.

X26:

White connector at the rear side of the instrument panel

X27:

Blue connector at the rear side of the instrument

S23:

Push button connector at the lower end of gear levers

X23:

Extra push button connectors at the lower end of gear levers

251

Model

Code

Page

31. Autocontrol 2.1

6000--8750

312

15. 4. 1995
1. 4. 1997

Содержание VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды

Valtra VALMET 6000, Руководство по ремонту

Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды