Valtra VALMET 6000 Скачать руководство пользователя

Страница: 743 / 1361

196

Model

Code

Page

42 Gearbox

420

6000--8750

15. 5. 1996

1. 9. 2002

Servo valve block on tractors which have 3---step quick---shift gear 660071---,

(Delta Powershift)

Picture 21.

Servo valve block on tractors which have Delta

Powershift,

660071 ---

(compare with picture 20 on previous

page).

Y1=Solenoid valve for diff. lock

Y2=Solenoid valve for PTO

Y3=solenoid valve for 4WD

Y4=Solenoid valve for reduction gear

Y6=Solenoid valve for overdrive

S16=Transmission oil temperature sensor (warning light)

S17=Transmission oil pressure sensor (warning light)

Note!

Sensor S17 in the picture above is fitted on the valve

block up to ser. no.

670581

. From ser. no.

670582 incl.

there

is a new sensor , which has two wires (earth and supply) and

the pressure values are 10---50 kPa. Apply Loctite 542 to the

threads of the sensor.

P=Oil supply from low pressure pump

V1=Valve spool for direct ratio of Delta Powershift

7= Pipe connector for connecting return oil side of working

hydraulics

Restriction/counter valve (Ø 1,6 mm restriction hole). This

valve is located in the 4WD pressure outlet, and in connection

with 650 DPS, also in C3 multi ---disc clutch pressure outlet.

Valve slide

) The adjustment of the valve slide has been done in the fac-

tory (grinding it so, that the clearance 9a and the correspon-

ding clearance at the left boring comes true).

Normally there is no need of adjustment. The slide is available

as spare part, when needed, adjustment by grinding.

Earlier model: The position of the adjusting screw is marked

with a punch point.

New model: The adjusting screw has been replaced with a

plug. in this way the possible faulty adjustments can be

avoided.

) Temperature sender unit for Agrodata --- display (option).

In this servo valve block the pressure---limiting valve (section

A---A) is the same as shown in figure

20B

on previous page.

Also the oil cooler safety valve (section B---B) and

the 4WD re-

striction/counter valve

(section C---C) are the same.

The servo valve block above has parts which are needed for

3---step quick---shift gear (Delta Powershift). Otherwise the

construction of this servo valve block corresponds to the valve

block presented in picture

20B

on previous page.

Important!

If repair work concerns the 3---step quick---shift

gear (Delta Powershift), see section

page

440/13

Also this valve has the cushioning valve for the PTO clutch,

Содержание VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды

Valtra VALMET 6000, Руководство по ремонту

Результаты поиска

Содержание VALMET 6000

Отзывы:

Похожие инструкции для VALMET 6000

Бренды по названию

Популярные бренды