Valentin DUOPRINT Скачать руководство пользователя

Страница: 83 / 96

DuoPrint Series

Error correction

10.15 Operating

Manual

Error message

Cause

Remedy

95 Scanner

layout

difference

Scanner data does not
correspond to bar code data.

Check adjustment of scanner.

Check scanner settings /
connection.

96 COM

break

Serial interface error.

Check settings for serial data
transmission as well as cable
(printer-PC).

97 COM

general

Serial interface error.

Check settings for serial data
transmission as well as cable
(printer-PC).

98 No

software

printhead FPGA

No printhead-FPGA data
available.

Please contact your
responsible distributor.

99 Load

software

printhead FPGA

Error when programming
printhead-FPGA.

Please contact your
responsible distributor.

100 Upper

position

Sensor signal up is missing

(option APL 100).

Check input signals /
compressed-air supply.

101 Lower

position

Sensor signal down is missing

(option APL 100).

Check input signals /
compressed-air supply.

102

Vacuum plate empty

Sensor does not recognise a
label at vacuum plate

(option APL 100).

Check input signals /
compressed-air supply.

103 Start

signal

Print order is active but device
not ready to process it.

Check start signal.

104

No print data

Print data outside the defined
label.

Selection of wrong module type
(design software).

Check selected module type.

Check selection of left/right
version.

105 Printhead

No original printhead is used.

Check the used printhead.

Contact your distributor.

106

Invalid Tag type

Wrong Tag type.

Tad data do not match the Tag
type in the printer.

Adapt data or use the correct
Tag type.

107 RFID

invalid

RFID module is not activated.

No RFID data can be
processed.

Activate RFID module or
remove RFID data from label
data.

108 GS1-128

invalid

Transferred GS1-128 bar code
is invalid.

Verify bar code data (see GS1-
128 bar code specification).

109 EPC

parameter

Error at EPC calculation.

Verify data (see EPC
specification).

Содержание DUOPRINT

































































































Результаты поиска

Содержание DUOPRINT

Отзывы:

Похожие инструкции для DUOPRINT

Бренды по названию

Популярные бренды

Valentin DUOPRINT, Руководство по эксплуатации

Результаты поиска

Содержание DUOPRINT

Отзывы:

Похожие инструкции для DUOPRINT

Бренды по названию

Популярные бренды