Vaillant ecoMAX pro 18 E Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 36

background image

Instructions for Use, Installation and Servicing ecoMAX pro

6

Sheet Metal Parts

This boiler contains metal parts (components) and care
should be taken when handling and cleaning, with
particular regard to edges.

Sealed Components

Under no circumstances must the User interfere with any
sealed component as this could result in a
potentially dangerous situation arising.

Electrical Supply Failure

This boiler must be earthed.
The boiler will not work without an electrical supply.
Normal operation of the boiler should resume when the
electrical supply is restored.
Reset any external controls to resume normal operation
of the central heating.
If the boiler does not resume normal operation turn the
mains reset switch off and on. If the boiler does not
resume normal operation after this the overheat
thermostat may have operated. The overheat
thermostat would only operate under abnormal
conditions and, under these circumstances; it would be
advisable to consult your installation / servicing
company.

2.10 Protection Against Freezing

The boiler has a built in frost protection programme as
long as the electricity and gas are left switched on.
This device operates the burner and system pump when
the temperature inside the boiler falls to 3 °C.
Any other exposed areas of the system should be
protected by a separate frost thermostat.
If the mains electricity and gas are to be turned off for
any long periods during severe weather, it is
recommended that the whole system, including the
boiler, should be drained to avoid the risk of freezing.
Make sure that, if fitted, the immersion heater in the
cylinder is switched off.
If you have a sealed water system contact your
installation/ servicing company as draining, refilling and
pressurising MUST be carried out by a competent
person.
As a safety feature the boiler will stop working if the
condensate drain becomes blocked. During freezing
conditions this may be due to the forming of ice in the
condense drain external to the house. Release an ice
blockage by the use of warm cloths on the pipe. The
boiler should then restart. Contact your installation/
servicing company if the fault persists.

2.11 Boilers Installed in a Compartment or Cupboard

If the boiler is fitted into a compartment or cupboard it
does not require ventilation openings.
Do not use the compartment or cupboard for storage.

Important information 2

«
...
4
5
6
7
8
...
»

Содержание ecoMAX pro 18 E





































Отзывы:

Нет отзывов

Похожие инструкции для ecoMAX pro 18 E

Бренд: U.S. Boiler Company Страницы: 104

BroilVection JF63 Gas

Бренд: Nieco Страницы: 40

STORAGE BOOSTER TANK

Бренд: John Wood Страницы: 8

Semia Condens F24 E

Бренд: Saunier Duval Страницы: 52

Бренд: Lamborghini Caloreclima Страницы: 88

Бренд: Raypak Страницы: 213

Бренд: Unical Страницы: 40

Бренд: New Yorker Страницы: 44

Бренд: Laars Страницы: 138

Бренд: Lamborghini Caloreclima Страницы: 68

MURELLE HT 25 GPL

Бренд: Sime Страницы: 76

EUTECTICEC-15DV

Бренд: Slant/Fin Страницы: 16

Бренд: Lang Страницы: 16

Бренд: Grant Страницы: 12

Бренд: Saunier Duval Страницы: 4

Бренд: Magikitch'n Страницы: 15

Бренд: Green Mountain Страницы: 36

Бренд: ApenGroup Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды