Vaillant ecoMAX pro 18 E Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 36

background image

Instructions for Use, Installation and Servicing ecoMAX pro

26

15 Servicing

15.3 Burner

Refer to Figs. 15.2, 15.3, 15.4 and 15.5.
Isolate the gas supply at the gas service cock.
Disconnect the gas supply at the union nut of the gas
service cock.

NOTE:

Do not disconnect at the gas valve.

Remove the two gas pipe bracket securing screws from
underside of inner case, see Fig. 15.2.
Drop down the control panel into the service position.
Remove the four screws from the chassis front, see Fig.
15.3.
Remove the chassis front by pulling it out at the top from
its retaining slots.

NOTE:

When replacing chassis front panel ensure the
bottom fits behind lip.

Disconnect the gas control valve plug at the gas control
valve, see Fig. 15.4.
Disconnect the electrical leads from the fan.
Remove the five combustion chamber front securing
nuts, see Fig. 15.5.
Gently remove the fan, gas control valve and burner
assembly from the combustion chamber complete with
the gas pipe bracket and seal.
Clean the burner with a soft brush taking great care not
to damage the front insulation. DO NOT use wire or
sharp instruments to clean the holes of the burner.
Inspect the burner for any signs of damage.
Removal of the burner from the fan, gas control valve
and burner assembly is not necessary during an annual
service.

CONTROL PANEL
SERVICE POSITION

SECURING
SCREW
(4 OFF)

CHASSIS
FRONT

GAS

CONTROL
VALVE

FAN

COMBUSTION

CHAMBER

FRONT

SECURING

NUTS

(5 OFF)

HEAT

EXCHANGER

IGNITION

LEAD

COMBUSTION

ANALYSER

TEST POINT

FLUE

ADAPTER

ELECTRODE

CONNECTOR

BURNER

COMBUSTION
CHAMBER

FAN

GAS
CONTROL
VALVE

GAS PIPE
BRACKET
& SEAL

SECURING
NUTS (5
OFF)

Fig 15.2

12708

Fig 15.3

12709

Fig 15.4

12710

Fig 15.5

1271

1

«
...
24
25
26
27
28
...
»

Содержание ecoMAX pro 18 E





































Отзывы:

Нет отзывов

Похожие инструкции для ecoMAX pro 18 E

Бренд: Riello Страницы: 44

Бренд: Weil-McLain Страницы: 4

Бренд: Zip Страницы: 16

Бренд: Olsen Страницы: 8

Бренд: Noritz Страницы: 38

Бренд: MONTAGUE Страницы: 36

Benchmark Aerco OMM-0122

Бренд: Watts Страницы: 122

Бренд: EASCO Страницы: 46

Super Xpress SX iQ Series

Бренд: OSO HOTWATER Страницы: 28

Бренд: Alpha Страницы: 44

Бренд: alfaplam Страницы: 32

Бренд: ROBUA Страницы: 32

Бренд: Truma Страницы: 5

Бренд: Ideal Boilers Страницы: 40

Classic FF 380 P

Бренд: Ideal Boilers Страницы: 40

Бренд: Ideal Boilers Страницы: 44

24kW Baykan Starplus

Бренд: GasTech Страницы: 26

ARCEUS EK 12 MT ERP UK

Бренд: E.C.A. Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды