Vaillant ecoMAX pro 18 E Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 36

Vaillant ecoMAX pro 18 E Скачать руководство пользователя страница 31

Instructions for Use, Installation and Servicing ecoMAX pro

31

17 Fault finding

17.2 Fault Memory

The fault memory stores details of the five most recent
faults. To display the fault memory, proceed as follows;
• With the interface in ‘normal’ mode, press and hold the
‘mode’ button (

) for 10 seconds until a flashing ‘0’

appears.
• Press the ‘mode’ button again.
• The 5 fault memory screens are now available to be
viewed, memory 1 being the most recent. Within each
memory screen, 5 additional screens provide further
information to assist the installer/engineer.

To cancel the fault memory mode proceed as follows;
• Press and hold the ‘mode’ button for 10 seconds until
the screen returns to the ‘user’ mode.

No. Memory screen type

Comments

1

Fault code

Fault code 1 – 26 (see page 31 – ‘Fault finding’)

2

Burner phase

Working phase

3

DHW temperature

No function

4

CH flow temperature

°C at time of fault

5

Tank temperature

No function

«
...
29
30
31
32
33
...
»

Содержание ecoMAX pro 18 E





































Отзывы:

Нет отзывов