Vaillant ecoMAX pro 18 E Скачать руководство пользователя страница 32

Страница: 32 / 36

Instructions for Use, Installation and Servicing ecoMAX pro

17 Fault finding

17.3 Fault Codes

Fault codes take priority over all other display functions
in the event of a system fault occurring.

Code Description

Comment

Ignition fault (lockout)

No gas; Insufficient gas; Incorrect gas valve adjustment; Electrode defect;

Failed to light

Ignition lead defect; Electronic igniter defective; Check air inlet duct;

Check connections to igniter unit

Ignition fault (lockout)

As above

Went out when lit

Overheat fault

Overheat stat operated; Maximum temperature exceeded;

Check thermistor connections; Air in system with thermistor at maximum

setting; Faulty overheat stat connection; Check that pump is wired into

appliance and not from programmer. This would cause no pump overrun

Central heating flow NTC fault

Flow NTC cable defective/broken NTC faulty

Flow thermistor not fitted correctly, Check pipe work configeration

F10

Central heating return NTC fault

Return NTC cable defective/broken NTC faulty

Check that thermistor attached correctly to pipe.

F11

No reception by main board

Connection fault between main PCB and interface; Faulty interface;

Faulty main PCB (processor), Check fan

F12

No reception by the local user interface

As F.11

F13

Main board fault

As F.11

F14

Central heating flow t° > 95° C

System fault; Possible external pump failure; Check NTC on flow

Check that pump is wired into appliance and not from programmer.

This would cause no pump overrun

F16

Flame detection fault

(flame presence >5 s after burner stop)

Gas valve defective

F17

Power supply <170 V

Check electrical supply / polarity, Check fan

F18

Local user interface fault

Connections; Faulty interface

F19

Central heating NTC unplugged

Check NTC connection

F20

MMI software incompatible with IRIS software

Possible connection fault

F24

Central heating return t° >90°C

System fault; Possible external pump failure; Check NTC on return;

Check that pump is wired into appliance and not from programmer.

This would cause no pump overrun.

F25

Maximum temperature rise slope

Possible external pump failure; Air in system restricting movement of water.

Insufficient circuit flow

F26

Maximum delta t

Check NTC on return; System fault – too restrictive?; Possible pump failure

Содержание ecoMAX pro 18 E





































Результаты поиска

Содержание ecoMAX pro 18 E

Отзывы:

Vaillant ecoMAX pro 18 E, Инструкция по использованию, установке и обслуживанию, Страница: 32 / 36

Результаты поиска

Содержание ecoMAX pro 18 E

Отзывы: