Vaillant ecoMAX pro 18 E Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 36

Vaillant ecoMAX pro 18 E Скачать руководство пользователя страница 24

Instructions for Use, Installation and Servicing ecoMAX pro

24

14 Conversion

• Again in screen ‘8’, Set the appliance fan speed/burner
to minimum by pressing the ‘-‘ key until ‘1’ (burner to
Pmin) is shown on the right hand side of the screen.
Press the ‘mode’ button again.

• Check the CO

2

value, which should be 10.5 %

±

0.2 %.

If adjustment proves necessary then proceed as
follows.
• Adjustment of the CO

2

at minimum rate is very

coarse, so carefully adjust the CO

2

with the (‘B’) offset

adjustment using a 2 mm allen key to 10.5 %, (rotate
clockwise to increase).
• After checking the combustion, press and hold the
‘mode’ button for 10 seconds to return to the normal
mode, showing the current flow temperature. Replace the
cap on the sampling point and refit the outer front case.
• Fit the LPG conversion label to the data badge.
• Re-commission boiler as described in the Installation
and Servicing Instructions supplied with boiler.

"A" throttle –
"Pmax" rotate
to increase

"B" offset adjustment
"Pmin" rotate
to increase

Fig 14.4

12705

Fig 14.5

12706

Appliance

CO

2

content at nominal

load for LPG in vol. %

ecoMAX pro 28E

10.5 %

±

0.2 %

«
...
22
23
24
25
26
...
»

Содержание ecoMAX pro 18 E





































Отзывы:

Нет отзывов