Vaderstad Spirit 600S Series Скачать руководство пользователя страница 22

Страница: 22 / 24

01.03.2017

ST600-900S

3. Positioning of the wheel The coulter arm

wheel can be set to four (4) positions.

For normal drilling depth (

1 - 5 cm) no

adjustment needs to be made. If you are

sowing peas or beans, or deeper sowing is

required, the results may be better if all of

the coulter arm wheels are changed. Refer

to the image next to this.

Deep sowing 5-9 cm

Shallow sowing 0-2 cm

Normal sowing 1-5 cm

Normal sowing 3-7 cm

Sowing seed

The following should be considered when setting the

drilling depth:

• Soil type?

• Quality of seedbed?
There are three settings that together affect the drilling depth:

1. Clips. The clips is the first and most important setting.

2. Coulter pressure. Do not use more coulter pressure than the conditions in the soil

require. Usually 50 bar is sufficient to ensure good seed sowing. In dry and difficult

conditions and/or for deep seed sowing it may be appropriate to increase the coulter

pressure.

Attachment 1.

• The sowing table below is only a recommendation! Something to START with!

• The seed sowing MUST be studied and decided in the field! Ascertain the seed amount and measure the

sowing depth!

• Too high a fan speed will result in uneven depth of sowing.

• Too low a fan speed will increase the risk of the seed blocking the seed hoses.

• It is also important to check to ensure that the correct seed amount is being put out in the field (therefore

that the calibration was correct). Advice If the actual sown amount in the field is, for example, 10 % too

high, increase the pulses per kg by 10 %.

• If the machine is equipped with BDA, you may need to increase the fan RPM slightly.

Fan

speed

(RPM)

Seed

drill

600S ST

800S ST

900S

Small seed sowing

2800

2900

3000

Grain

3300

3400

3500

7. Rotors

Grain rotor

Adapted to all normal feed rates of grains

such as cereals and peas, (possibly fertiliz-

ers).

approx 80-100 kg/ha and

upwards

Grass seed rotor

Adapted to various types of grass

seed blends.

approx 10-60 kg/

Rapeseed rotor

Adapted for low feed rates of

small seed products.

approx 2-12 kg/ha

Special rotors

For low feed rates of large seed sowing (hybrids of rye,

maize, catch-crop mixtures that contain large seeds).

up to approx 80-100 kg/ha

• Moisture?

• Plant residues that could cause resist-

ance?

For rapeseed feed amount below approx. 2 kg/ha.

Note the positioning of the flat ring, with the flat

side opposite the other rings!

Содержание Spirit 600S Series

























Результаты поиска

Содержание Spirit 600S Series

Отзывы:

Похожие инструкции для Spirit 600S Series

Бренды по названию

Популярные бренды

Vaderstad Spirit 600S Series, Быстрый старт

Результаты поиска

Содержание Spirit 600S Series

Отзывы:

Похожие инструкции для Spirit 600S Series

Бренды по названию

Популярные бренды