vacuubrand VACUU-PURE 10C Скачать руководство пользователя страница 7

Страница: 7 / 96

20901224_EN_VACUU·PURE 10C_V1.8_221122

Introduction

1.2.2

1.2.2 Display conventions

Display conventions

Warning levels

DANGER

Indicates an imminent hazardous situation.

Disregarding the situation could result in extremely

serious injury or death.

Take appropriate action to avoid dangerous

situations!

WARNING

Warns of a potentially hazardous situation.

Disregarding the situation could result in serious injury

or death.

Take appropriate action to avoid dangerous

situations!

CAUTION

Indicates a potentially hazardous situation.

Disregarding the situation could result in minor injury or

damage to property.

Take appropriate action to avoid dangerous

situations!

NOTE

Indicates a potentially harmful situation.

Disregarding the situation could result in damage to property.

Additional notes

Information or specific recommendation which must be

observed.

Important information for trouble‑free operation of your product.

Helpful tips + tricks

Additional information

IMPORTANT!

Presentation

conventions

Содержание VACUU-PURE 10C

































































































Результаты поиска

Содержание VACUU-PURE 10C

Отзывы:

Бренды по названию

Популярные бренды

vacuubrand VACUU-PURE 10C, Инструкция по эксплуатации

Результаты поиска

Содержание VACUU-PURE 10C

Отзывы:

Бренды по названию

Популярные бренды