manualshive.com logo in svg

vacuubrand VACUU-PURE 10C, Инструкция по эксплуатации

Поделиться
Скачать
vacuubrand VACUU-PURE 10C Скачать руководство пользователя страница 63

63

20901224_EN_VACUU·PURE 10C_V1.8_221122

Error messages

Error

Error

 

`

Possible cause

 

3

Remedy 

Personnel

Warning

 

flashing rate 

5x

 

`

Supply voltage for 

control board in 

critical range.

 

3

Remove any 

connected 

VACUU·BUS 

accessories if too 

many or replace if 

faulty.

Specialist

Warning

 

flashing rate 

6x

 

`

Message: 

VACUU·BUS 

accessories (vacuum 

sensor overpressure).

 

3

Check pressure in 

system and reduce 

if necessary.

 

3

Check vacuum 

sensor, calibrate if 

necessary. Replace 

defective sensor.

Operator

 

`

Message: 

VACUU·BUS 

accessories (cooling 

period for level 

sensor active).

 

3

Cooling period 

for level sensor is 

running (5 min): No 

action necessary.

 

3

Extend cooling 

period for level 

sensor.

 

3

Empty full receiving 

flask.

 

`

Message: 

VACUU·BUS 

accessories (level 

sensor triggers 

although level 

has not yet been 

reached).

 

3

Calibrate level 

sensor or replace 

defective level 

sensor.

Specialist

Warning

 

flashing rate 

7x

 

`

 Other warnings.

 

3

Send in vacuum 

pump.

Resp. 

specialist

Error – Cause – 

Remedy

Содержание VACUU-PURE 10C

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды