vacuubrand VACUU-PURE 10C Скачать руководство пользователя страница 24

Страница: 24 / 96

20901224_EN_VACUU·PURE 10C_V1.8_221122

Product description

3 Product description

Product description

The

VACUU·PURE 10C

is a chemical‑resistant, oil‑free, air‑cooled

screw vacuum pump for the vacuum range from atmospheric

pressure to 10

‑3

mbar in the lab.

As a component of the VACUU·BUS system, the vacuum pump

offers numerous connection and expansion options for a wide

variety of applications.

Product features

The operating principle of the vacuum

pump is based on the non‑contact

gap seal.

The suction chamber of the vacuum

pump is oil‑free.

The drive side of the vacuum pump

is protected against corrosion by

sealing gas (= aspirated ambient air)

through pumped media.

An internal non‑return valve protects the vacuum pump against

faulty start‑up. A vacuum‑tight shutdown can be achieved by an

additional external valve.

Material compatibility

The vacuum pump has a high chemical resistance

The entire

wetted area is made of chemical‑resistant materials,



see

chapter:

8.1.3 Wetted materials on page 83

Due to the high level of water vapor and condensate compatibility

of the vacuum pump, no gas ballast is required.

Condensate or

drops of liquid that enter the vacuum pump with the pumped

medium are easily conveyed through the vacuum pump.

Product description

VACUU·BUS

system

Technical

characteristics

Chemical resistant

Compatible with

water vapor and

condensate

Содержание VACUU-PURE 10C

































































































Результаты поиска

Содержание VACUU-PURE 10C

Отзывы:

Бренды по названию

Популярные бренды

vacuubrand VACUU-PURE 10C, Инструкция по эксплуатации

Результаты поиска

Содержание VACUU-PURE 10C

Отзывы:

Бренды по названию

Популярные бренды