manualshive.com logo in svg

vacuubrand VACUU-PURE 10C, Инструкция по эксплуатации

Поделиться
Скачать
vacuubrand VACUU-PURE 10C Скачать руководство пользователя страница 53

53

20901224_EN_VACUU·PURE 10C_V1.8_221122

Commissioning (operation)

5.4  

5.4  Connect / remove VACUU·BUS accessories

Connect / remove VACUU·BUS accessories

Connect VACUU·BUS accessories

1. 

1. Stop the vacuum pump and switch off the vacuum pump at 

the power switch.

2. 

2. Insert the VACUU·BUS plug of the accessory into the lower 

socket on the back of the vacuum pump.

3. 

3. Switch on the vacuum pump at the power switch. The 

connected accessories are automatically detected.

 

5

VACUU·BUS accessories connected.

Remove VACUU·BUS accessories

.

1. 

1. Stop the vacuum pump and switch off the vacuum pump at 

the power switch.

2. 

2. Unplug the VACUU·BUS accessories on the back of the 

vacuum pump.

3. 

3. Carry out a BUS scan of the vacuum pump to deregister the 

accessories from the vacuum pump BUS system, 

 

see

 

chapter:

 

5.4.1 VACUU·BUS detection on page 54

5.4.1 VACUU·BUS detection on page 54

.

 

5

VACUU·BUS accessories removed.

General notes on VACUU·BUS components

 

ƒ

Use Y‑adapters and extension cables to connect and use 

several VACUU·BUS components in parallel.

 

ƒ

A maximum of six VACUU·BUS components can be connected 

and used in parallel.

 

ƒ

A  maximum  of  four  components  of  the  same  type  can  be 

connected.

 

ƒ

Each connected VACUU·BUS component must have a different 

VACUU·BUS  address.  The  connection  of  two  components 

with  identical  VACUU·BUS  addresses  leads  to  errors  in  the 

BUS  system.  (Reconfiguration  of  the  VACUU·BUS  address 

of  a  component:  see  operating  manual  of  a 

VACUUBRAND

VACUUBRAND 

controller, e.g., VACUU·SELECT).

 

ƒ

Note the maximum permissible load of 11 W at the VACUU·BUS 

port.

Remove 

VACUU·BUS 

accessories

VACUU·BUS 

accessories –

 

 General information

Connect 

VACUU·BUS 

accessories

Содержание VACUU-PURE 10C

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды