![background image](http://html1.mh-extra.com/html/v2/torq500a-230v/torq500a-230v_manual_847092015.webp)
ENGLISH
- 35 -
8 - PROGRAMMING THE GATE PATH
To start the system up, one of the following programming
procedures must be carried out:
-
basic programming of the automation’s movement:
self-learning of the manoeuvre times and of the slowdown
start points.
-
advanced programming of the automation’s movement: self-
learning of the manoeuvre times and manual setting of the
slowdown start points.
The procedure for programming the partial opening is used to
modify the default opening value.
m
If, at the start of the following procedures, the
“set”, “radio” and “start” LEDs flash, it means that
the programming protection has been activated – see
Paragraph 13.1.
m
To interrupt the following programming sequences at
any time, press the SET and RADIO buttons simultaneously
or wait 10 seconds.
8.1 - BASIC PROGRAMMING OF THE
AUTOMATION MOVEMENT
1.
Position the door in an intermediate position
2.
Press the SET button for 1 second: the yellow “set” LED
flashes
3.
Press the SET button for 1 second, the yellow “set” LED lights
up steadily
4.
The control unit performs a partial opening
m
WARNING! If the automation starts the movement
with the closing instead of the opening it is necessary:
• exit programming by pressing SET and RADIO
simultaneously
• move DIP8, see paragraph 5.2
• redo the run schedule starting from point 1
5.
The control unit performs a total closure
6.
The control unit performs a total opening
7.
The control unit performs a total closure
8.
End of programming: the LEDs return to the normal operating
configuration
8.2 - PROGRAMMING OF THE WIDTH OF THE
PEDESTRIAN OPENING
m
Prior to proceeding with this programming procedure,
first verify whether either the “basic automation movement
programming” or the “advanced programming” have been
completed.
1.
Position the door in the fully closed position
2.
Press the SET button for 2 seconds: the yellow “set” LED
flashes
3.
Press the START button for 1 second: the yellow “set” LED
lights up steadily
4.
Press the START button or a key of a programmed transmitter
or a wired command
5.
The control unit starts opening the door
6.
When the gate reaches the position for pedestrian
opening, press the START button or a key of a programmed
transmitter: the control unit performs the stop and performs
the total closing of the leaf, the yellow “set” LED goes off.
7.
End of programming: the LEDs return to the normal operating
configuration
8.3 - ADVANCED PROGRAMMING OF THE
AUTOMATION MOVEMENT
1.
Position the door in an intermediate position
2.
Press the SET button for 2 seconds: the yellow “set” LED
flashes
3.
Press the RADIO button for 1 second: the yellow “set” LED
lights up steadily
4.
The control unit performs a partial opening: the yellow “set”
LED flashes
5.
The control unit waits for a possible change in the direction
of movement for 8 seconds (dip 8). Press the SET button to
proceed
6.
The control unit performs a total closure: the yellow “set”
LED remains on steady
7.
Press the SET button or a programmed transmitter key
8.
The control unit performs the opening
9.
If slowing down is desired during opening, during the
movement press the SET button or a transmitter button
programmed to set the slowdown start point. otherwise, wait
for the movement to complete
10.
The control unit completes the opening
11.
Press the SET button or a programmed transmitter key
12.
The control unit performs a total closure
13.
If slowing down is desired during closing, during the
movement press the SET button or a transmitter button
programmed to set the slowdown start point. Otherwise,
wait for the movement to complete
14.
The control unit completes closing: the yellow “set” LED
turns off
15.
End of programming: the LEDs return to the normal operating
configuration