UV Pure Technologies Hallett 30, Инструкция по эксплуатации

Страница: 30 / 40

Hallett
30 1” Instruction Manual
Released on 1-Sep-16
– X800058R
Page 30 UV Pure Technologies Inc. © 2016
10 Bearing & Base for Wiper Shaft 1 E300142
11 Bearing O ring Seal 1 350011
12 Insert Adapter for Flow Regulator 1 C300075
13 Internal Flow Regulator 1 550201
14 Bracket
– Top, Plain End
1 C300012
15 1/4
” Lock Washer
8 650001
16 Bracket Fastener, 1/4-
20 x 5/8” long
8 650000
17 Top End Cap c/w Shaft guide 1 C300055
18 Shaft Retaining Ring (included in Seal Kit) 1 N/A
19 Seal Washer for SS Hose
– sold in pairs
2 C500009
20 Rubber Washer
– Motor Shaft (Included in Motor Kit)
1 N/A
21 Foam Pad for Motor (Included in Motor Kit) 1 N/A
22 Bottom Bracket Assy c/w Lamp Wire Harness 1 C300068
23 Bottom End Cap Assy
– Motor End c/w Seals
1 C300078
24 Quartz O ring seal (included in Quartz Kit or Seal Kit) 2 N/A
25 Wiper O ring Seal (included in Seal Kit) 1 N/A
26
Washer, Teflon 5/8” ID x 1” OD (included in Seal Kit)
1 N/A
26A Plastic Washer (included in Wiper Assembly Kit) 1 N/A
27 U Cup Seal for Wiper (included in Seal Kit) 1 N/A
28 Solenoid Shut-off Valve (Normally Closed) 1 550055
29 Display Pad (Membrane switch) 1 E100016
30 Purge Valve Assembly 1 X500000
31 Cold Air Kit 1 X500001
32 Replacement Fuse Pack for 120V units (6 in pack) 1 E400020
33 Replacement Fuse Pack for 240V units (6 in pack) 1 E400021
34 Transient Voltage Surge Suppressor for 115V systems 1 150207
35 Circuit board
– Drinking Water
1 E100065
36 Hallett Diagnostic Tool 1 X100012
37 External 27.4gpm Flow restrictor
– NSF approved
1 CE33
*Older generation Hallett 30s used semi-circular reflector panels
– to reorder
these panels, use p/n E300084T; UV sensors for these units are p/n C100006.
Cleaning/Removing the Quartz Sleeve
Note that numbers in parentheses refer to Figure 4B.
Step 1: Use a bottle cleaning brush with a long handle to scrub the inside of the
quartz sleeve. Scrub and flush with clean water repeatedly to clean the quartz.
Use a squeeze bottle to apply water or solution to the quartz sleeve to keep the
area tidy.
Note: Keep the rest of the unit free from moisture. Examine the
quartz by looking through the unit.
Step 2: If the quartz is still dirty, use a scale remover such as CLR or Lime
Away and apply it to the inside of the quartz sleeve. Citric acid, available at a
drug store, can also be used.
Always flush with clean water afterwards.
Step 3:
Once the quartz is clean, reassemble the unit (see below). Replace any
seals that appear to have been damaged.
Step 4:
If the quartz is still not clean, it requires replacement. This is done by
removing the bottom quartz seal assembly.
Step 5: Disconnect the wiper motor (5) from the bottom bracket (22) by undoing
the three nuts. See Figure 4C. Pull off the motor plate and foam pad (21) from