manualshive.com logo in svg

UV Pure Technologies Hallett 30, Инструкция по эксплуатации

Поделиться
Скачать
UV Pure Technologies Hallett 30 Скачать руководство пользователя страница 11

Hallett 30 1” Instruction Manual 

Released on 1-Sep-16 

– X800058R

 

Page 11 

UV Pure Technologies Inc. © 2016

 

TIGHTEN HOSE

AS SHOWN

PROTECT AREA

FROM WATER,

DIRT, OR SOLDER ETC.

 

Figure 1C 

 

Step 3:

 Two wall brackets, with two 1/4" slotted holes each are provided on the 

unit. 

The unit should be secured vertically to a solid wall large enough to 

cover the complete backside of the unit 

– See Figure 1D.  

Install the top two 

fasteners (not provided) into the wall, and slide the unit onto them using the 
slotted holes in the upper brackets. Then install the bottom two fasteners. 

Do 

not

 install the unit horizontally. Leave clearance over the unit for lamp removal.

 

Connecting the Pipes 

We recommend that a qualified plumber or certified technician perform the 
water connections for your Hallett. 

Water must flow into the inlet at the 

bottom of the unit. The outlet is located at the top of the unit. 

Install the 

valve upstream of the unit. 
 

Step 1:

 Shut off the water supply. 

Caution: 

Always turn off the water supply 

before modifying or disconnecting any piping. Always open a faucet after 
shutting off the water supply to relieve water pressure and ensure that the water 
has been completely shut off.  
 

Step 2:

 If you have decided to install an optional bypass line and drain, you may 

begin to install these fittings at this point. See Figure 1B for more information on 
how to connect optional bypass piping and drain.  
 

Step 3:

 Connect the solenoid valve to the plumbing just upstream of the unit 

(before the unit). Note the solenoid valve ensures that should the system fail, 
due to power loss, color in the water or low UV lamp output, the system will fail 
in safe mode and shut down the flow of water to your tap. The direction of flow 
through the valve is important 

– 

verify flow direction with label on the valve

. 

Caution: over tightening a metal fitting into the valve will cause it to crack. 

Содержание Hallett 30









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды