manualshive.com logo in svg

UV Pure Technologies Hallett 30, Инструкция по эксплуатации

Поделиться
Скачать
UV Pure Technologies Hallett 30 Скачать руководство пользователя страница 16

Hallett 

30 1” Instruction Manual

 

Released on 1-Sep-16 

– X800058R

 

Page 16 

UV Pure Technologies Inc. © 2016

 

When complete, replace the front cover by first reconnecting the 6-pin ribbon 
cable to the port marked ‘DISPLAY’ (ensure the black connector is aligned 
properly and 

do not miss any pins

). Place the front cover in its rest position. 

 
Replace the top cover and screw it down 

Cold Air Kit 

If cold room conditions cannot be avoided, the Cold Air Kit should be installed. 
The kit also helps when water temperatures are very low.   The kit consists of 
two cover plates, two lamp insulators and two pieces of foil insulation. The cover 
plates are to be placed on the top aluminum plate to cover the convection holes. 
The foil insulation is placed between the lamp base and bottom endcap. The 
lamp insulators are to be wrapped around the bottom of the lamps just below 
the bottom aluminum plate. See Figure 1G.  
 
If during the summer months the room temperature exceeds 20°C (68°F), the 
Cold Air Kit may be removed and then reinstalled for winter months only. 

 

COVER PLATE

TOP VIEW OF UNIT

LAMP 
INSULATOR

BOTTOM VIEW OF UNIT

FOIL INSULATION - INSTALL 
BETWEEN LAMP & BTM 
ENDCAP. LIFT LAMP TO
INSTALL.

 

 

Figure 1G

 

Содержание Hallett 30









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды