manualshive.com logo in svg

UV Pure Technologies Hallett 30, Инструкция по эксплуатации

Поделиться
Скачать
UV Pure Technologies Hallett 30 Скачать руководство пользователя страница 31

Hallett 30 1” Instruction Manual 

Released on 1-Sep-16 

– X800058R

 

Page 31 

UV Pure Technologies Inc. © 2016

 

the mounting standoffs and unplug the motor. Set the motor aside, holding it by 
the body, not the wires. 

Do not place the motor in any location where it can 

be exposed to moisture

. 

 
Step 6

: Remove the bottom Bracket (22) by undoing the four fasteners in an 

alternating pattern (top left, bottom right, bottom left, then top right). The bottom 
End Cap (23) will drop as the bracket is removed. Support the quartz sleeve as 
you remove these two items. 
 

Step 7

: Remove the quartz sleeve by removing the top and bottom O rings (24). 

Lift the quartz sleeve out of the unit. 
 

Step 8

: Inspection of wiper seals can be done now. This is a two-step process. 

First, remove the rubber washer (20) and shaft retaining ring (18) and place 
them in a safe place. Second, lift the shaft adapter (6A) out of the bottom End 
Cap (23). Check the U-cup seal (27) Wiper O ring (25) 

– replace/clean if 

necessary.  Re-install shaft adapter (6A). Replace the wiper retaining ring (18) 
by inserting it into the grooved area on the shaft adapter. Replace the rubber 
washer (20). 

 
Step 9

: Install the new quartz sleeve into the unit and center it vertically. 

Be 

careful not to chip the ends.  

Support the quartz for the next two actions. 

 
Step 10

: Replace the top and bottom O rings (24), keeping the quartz centered 

vertically in the unit. 
 

Step 11

: Replace the bottom End Cap (23) and bottom Bracket (22) by installing 

the four fasteners in an alternating pattern (top left, bottom right, bottom left, 
then top right) 

(lock washers must be installed)

. Ensure that the welded elbow 

is at the backside of the unit. Ensure that the bottom End Cap (23) sits centered 
in the bottom Bracket (22). 

USE AN 11/32" NUT DRIVER

TO REMOVE NUTS

ALIGN MOTOR SHAFT

WITH SLOT IN WIPER SHAFT

(REMOVE FOAM PAD TO SEE)

DO NOT OVER-

TIGHTEN NUTS

RUBBER WASHER TO
BE INSTALLED ON

WIPER SHAFT BEFORE

MOTOR

 

Figure 4C 

Содержание Hallett 30









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды