14
DS1033-124
15
DS1033-124
In 1033/471 model, if incoming calls are disabled, the GSM module is turned off and it is automatically
activated again, when it is necessary to perform an alarm call. In this way the current consumption is
reduced: this is very useful when the alarm control panel that supplies the dialer is powered by the
backup battery. The GSM module operates in a similar way in 1033/472 model, with the following
parameters con
fi
gurations: parameter 503 = 0 or parameter 503
≠
0 and parameter 508 = 0.
Trunk access code for PABX
: if the telephone dialer is connected to the PSTN line by a PABX, it is
possible to con
fi
gure the trunk line access code, that will be automatically dialled before the programmed
telephone numbers.
Telephone channel priority
: with the telephone dialer 1033/472 model, equipped with both PSTN and
GSM modules, it is possible to select which of them will be used for the alarm message sending. If the
priority telephone channel is not available (for example for a line failure or for no GSM
fi
eld), when it is
necessary to send an alarm message, the telephone dialer will automatically use the other channel.
Call delay
: it determines the input activation time before an alarm signalling is generated. The correct
con
fi
guration of this parameter allows to avoid false alarm signalling, because, for example, the user has
forgotten to disarm the alarm system.
Call cycles
: it determines how many times the call cycle is repeated. The call cycle includes the sequential
call of the telephone numbers associated to the call diversion function and associated to the alarmed
input.
In the the following table are shown the telephone parameters, the allowed values and the default values.
Parameter Description
Allowed values
Factory
value
Telephone parameters programming
501
Dial tone check
0 = disabled
1 = enabled
0
502
Answer check
0 = disabled
1 = enabled
0
503
Rings for incoming call
0, 1, 3, 5, 7
5
507
Trunk access code for PABX
4 digits max
Button
: The trunk access code,
if already stored, is deleted.
508
Telephone channel priority
0 = PSTN
1 = GSM
0
610
Call delay
0 = 250 ms
1 = 3 s
2 = 20 s
0
620
Call cycles
1, 2, 3, 4, 5
3
After entering the value, press button
to con
fi
rm.
It is possible to check the parameter current con
fi
guration, or if a value is correct, by entering the respective
parameter followed by button
instead of button
.
§
•
•
•
•
2.3.3 TELEPHONE CONNECTION TEST
GSM field test (1033/471 and 1033/472 models)
It allows to check the GSM
fi
eld level. To perform the test, follow the instructions below:
User action
Dialer answer
Enter
504#
Press 0 to start the GSM
fi
eld test
Enter
0
Please wait
. Some beeps are emitted; during this time the
test is performed. At the end, are possible the following
answers:
Excellent GSM
fi
eld
Good GSM
fi
eld
Low GSM
fi
eld
No GSM
fi
eld
•
•
•
•
GSM call test (1033/471 and 1033/472 models)
It allows to perform a test call with the GSM module. The called number is the call diversion function
number and only the main message is played. To perform the test, follow the instructions below:
User action
Dialer answer
Enter
505#
Press 0 to start the test call
Enter
0
The test call is performed
Warning
: before performing the test, check that the call diversion number has been programmed
(parameter 100).
PSTN call test (1033/470 and 1033/472 models)
It allows to perform a test call with the PSTN module. The called number is the call diversion function
number and only the main message is played. To perform the test, follow the instructions below:
User action
Dialer answer
Enter
506#
Press 0 to start the test call
Enter
0
The test call is performed
Warning
: before performing the test, check that the call diversion number has been programmed
(parameter 100).
2.3.4 PROGRAMMING PARAMETERS
It is possible to con
fi
gure the programming procedure, by enabling or disabling the voice driven menu
and the selected language. If voice messages are disabled in programming mode, the dialer will signal the
operations to be performed or their result as follows:
Short beep: enter a value
Long beep: error
Beep-beep: the entered value has been stored
Parameter Description
Allowed values
Factory
value
Programming parameters
640
Language selection for pre-recorded
messages
0 = Italian
1 = English
0
650
Voice messages in programming mode
0 = disabled
1 = enabled
1
After entering the value press the button
to con
fi
rm.
It is possible to check the parameter current con
fi
guration, or if a value is correct, by entering the respective
parameter followed by button
instead of button
.
•
•
•
