urmet domus 1033/470 Скачать руководство пользователя страница 13

DS 1033-124

LBT 8355

http://www.urmetdomus.com

e-mail:[email protected]

FILIALI

20151 MILANO - V.Gallarate 218
 

Tel. 02.380.111.75 - Fax 02.380.111.80

00043 CIAMPINO (ROMA) V.L. Einaudi 17/19A
 

Tel. 06.791.07.30 - Fax 06.791.48.97 

80013 CASALNUOVO (NA) V.Nazionale delle Puglie 3
 

Tel. 081.193.661.20 - Fax 081.193.661.04

30030 VIGONOVO (VE) - V.del Lavoro 71
 

Tel. 049.738.63.00 r.a. - Fax 049.738.63.11

66020 S.GIOVANNI TEATINO (CH) - V.Nenni 17
 

Loc. Sambuceto Tel. 085.44.64.851

 

Tel. 085.44.64.033 - Fax 085.44.61.862

SEDE

URMET DOMUS S.p.A.
10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Telef. 

+39 011.24.00.000 (RIC. AUT.)

Fax 

+39 011.24.00.300 - 323

Area tecnica
servizio c39 011.23.39.810

Fabbricato da Urmet Electronics Limited (un’azienda del 
gruppo Urmet) - Made in PRC.
Manufactured by Urmet Electronics Limited (an Urmet 
group company) - Made in PRC.

7. POCKET GUIDE

Cut out along broken lines.

Alarm calls interruption

Enter 22 during the pause of alarm message repeat.

Remote management

1.  Digit the dialer telephone number

2. Enter 

password

 + 

 

3.  Digit the command:

 

1 = Thermostat ON

 

2 = Thermostat OFF

 

3 = Relay closing

 

4 = Relay opening

 

9 = environmental listening activation

 

0 = telephone connection closing

In the same remote management session can be queued 

several commands; after one minute of inactivity, the telephone 

connection is automatically closed.

§

Содержание 1033/470














Отзывы: